Hi, can someone tell me how to measure for stair carpet? is it just double the lengh? thanks

Measure the length of the tread and riser, combined. Typically this will be 17 inches or so. Add at least an inch or two for good measure then, assuming all the stairs are the same, multiply by the number of stairs and, in most cases add for one additional riser. This is for straight stairs with no landings or turns. For pie-shaped stairs one needs to measure the longest points for the trad portions.

Posted on Dec 22, 2008

if you are staining the edges and both sides it will work out as follows

Each flat side is roughly 5.28 square feet or 10.5 square feet total per board.

The edges add rougly another 2.4 square feet so rough answer would be 13 square feet per board.

Each flat side is roughly 5.28 square feet or 10.5 square feet total per board.

The edges add rougly another 2.4 square feet so rough answer would be 13 square feet per board.

Jul 10, 2016 | Calculators

cups measure volume , you wish to measure weight. Try 100 ml equivalent , or a tiny bit more. 100ml is just over 3 ounces of liquid equivalent. In theory one ml is the same as 1 gram but the measure is for liquid. (water I think) A teaspoon full is about 5ml/5 grams. Slightly over the 100ml mark is a very rough estimate. A weighing scale really would be better

Jun 08, 2015 | Calculators

Hi

Enter the measurement in millimeters and divide by 25.4 to give you the same measurement in inches.

Cheers

Enter the measurement in millimeters and divide by 25.4 to give you the same measurement in inches.

Cheers

Mar 06, 2015 | Calculators

Foot is a measure of length. Cubic foot is a measure of volume.

You might measure the length of your bedroom in feet. If you measure the length, the width, and the height, and multiply them together then you get the volume of the room in cubic feet.

You might measure the length of your bedroom in feet. If you measure the length, the width, and the height, and multiply them together then you get the volume of the room in cubic feet.

Oct 06, 2014 | Calculators

554 feet or 169 meters. See http://en.wikipedia.org/wiki/Minisink,_New_York

Oct 04, 2014 | Calculated Industries 6020 Scale Master...

hi there,

Firstly make sure that you are in the right angle measurement (e.g. Degrees, Radians or Gradians.) To do this find the button with DRG written in orange above it then press 2nd F and this button and it will move you to the next type of measurement. Do this until you have the correct angle measurement.

Then press 2nd F tan (in orange above it you will see tan^-1) and type in the ratio and then press =.

And there you go.

Firstly make sure that you are in the right angle measurement (e.g. Degrees, Radians or Gradians.) To do this find the button with DRG written in orange above it then press 2nd F and this button and it will move you to the next type of measurement. Do this until you have the correct angle measurement.

Then press 2nd F tan (in orange above it you will see tan^-1) and type in the ratio and then press =.

And there you go.

Apr 13, 2014 | Sharp Calculators

If you know the center, measure the distance between the center and one point on the circumference. Measure with the opening of a compass and report on a ruler, or use a ruler.

Take the measure of the radius and multiply by 2. Any other indirect way of getting the radius does not constitute a measure but a calculation.

The diameter of a circle enters in two formulas.

Length of Circumference: C=Pi*D (D diameter) ====>**D=C/Pi**

Area of the disk A=Pi *D^2/4 =====>**D=SQRT(4*A/Pi)**, SQRT is the square root operation.

Take the measure of the radius and multiply by 2. Any other indirect way of getting the radius does not constitute a measure but a calculation.

The diameter of a circle enters in two formulas.

Length of Circumference: C=Pi*D (D diameter) ====>

Area of the disk A=Pi *D^2/4 =====>

Dec 31, 2013 | Calculators

Angles may be measured in three angles:degree, radian and gradians (grads).

tan(45 deg)=1

tan(45 radians)=1.61977

If your problems require angles to be measured in degrees, make sure that the calculator's angle unit is set to degrees.

In RUN screen press [SHIFT][MENU] (SetUp) select the angle line and press function key under the tab Deg (should be F1).

tan(45 deg)=1

tan(45 radians)=1.61977

If your problems require angles to be measured in degrees, make sure that the calculator's angle unit is set to degrees.

In RUN screen press [SHIFT][MENU] (SetUp) select the angle line and press function key under the tab Deg (should be F1).

Sep 17, 2013 | Casio FX-9860G Graphic Calculator

A yard is 1 dimensional so just a straight line.

A cubic yard is 3 dimensional so imagine a box with all sides being 1 yard long, the volume of this box is a cubic yard.

A cubic yard is 3 dimensional so imagine a box with all sides being 1 yard long, the volume of this box is a cubic yard.

May 04, 2011 | Calculators

Dec 02, 2016 | Calculators

480 people viewed this question

Usually answered in minutes!

×