Question about RCA Audio Players & Recorders

1 Answer

Power button is blinking red and it wont turn on

Posted by on

  • Ryan Bolduk Sep 02, 2008

    its an RCA hometheater suround sound rt2760

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

Read your manual and look for some typ of reset in Protect mode and how to reset it, or download a repair manual from on line and that will help all you self tech doers....read closely...ok
Radricktip

Posted on Sep 02, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

The red light on my Marantz SR5008 keeps flashing and wont turn on. How can I fix this


Disconnect everything and then plug in only the power. If the light still blinks, the PS is probably damaged and will need to be serviced. If the light doesn't blink, you have a shorted connection. Speaker wires are probably the most likely.

Oct 07, 2014 | Marantz SR5001

1 Answer

What can i do to stop the red light blinking for marantz sr5007?


Turn off the power using X.
2 Press X ON/STANDBY while simultaneously pressing PRESET CH + and PRESET
CH -.
3 Once the display starts flashing at intervals of about 1 second, release the two
buttons

Aug 09, 2014 | Marantz SR5007 Home Theater AV Receiver

2 Answers

Pioneer VSX-72TXV wont power up. mcacc light just blinks.. unit does not have a video 2 button on the face.


try holding the "TUNE -" button and the ZONE 2 on/off button and see if it turns on. If its turns on, but turns back off again, you either have a problem with your speakers (try disconnecting them) or there is a problem with the receiver that needs to be repaired.

Dec 06, 2013 | Pioneer VSX-72TXV Receiver

1 Answer

The receiver was on....working properly...and then it went off and the light on the poewr button started blinking red....I had assumed it was overheated so I ventilated the cabinet and let it sit...


There is a good chance you have a faulty capacitor. There are lots electronic devices out there right now that are failing to power up or just shutting down on there own these days. Turns out many manufacturers of electronic boards installed faulty caps in their products.

I hate to say it but that sounds like the problem to me.

Solutions

1. Have it fixed by a professional
2. Open it up, Inspect the power board for bulged/leaking caps. If you find some you know you have found a problem. Replace the board.
3. Replace individual caps that are faulty. This takes a few soldering skills but can save you $$$$$$

Caps are very inexpensive and can be found at your local electronics store or online.

Hope this helps and thanks for using fixya

Kaufman605

Dec 11, 2010 | Denon AVR-885 Receiver

1 Answer

When i power up the reciever and watch tv the reciever turns off and the power button blinks red. I unpluged the reciever for 1 hour and put it back on. nothing changed. i even unpluged the speaker wires...


You have an internal short in your receiver could be power supply or most likely a output transister. There is a code to the blinking red light check your manual it may list the number of blinks with problem. However its not a simple fix. plus make sure HDMI cable is unplugged when reseting receiver if this cable has a short it may cause it to. Sorry to hear the bad news, nice receiver
GOOD LUCK....

May 24, 2010 | Denon AVR-1508 Receiver

3 Answers

Pioneer VSX-1019 with a flashing red MCACC


you can "release" the error by pressing the "down arrow" and the "zone 2 on/off" for 2 seconds.

Mar 11, 2010 | Pioneer VSX-1019AHK A/V receiver

1 Answer

Denon AVR-1906 Reciever is not working. Was watching a movie and then it suddenly shut off. Now, the power light is blinking red. When I try to power it on again it starts to boot up but then turns off...


speaker terminal are short circuit,switch power off connect speaker properly then switch power back.
-the ventilation holes of the set are blocked-turn power off and make good ventilation around leave the set to cool and turn power back.
-the unit is operating at continuous high power turn it of and allow for cool down and switch it back.

Jun 01, 2008 | Denon Audio Players & Recorders

1 Answer

Innovage jumbo universal remote


TV codes 0013, 0018, 0028, 0031, 0034, 0043, 0046, 0052, 0058, 0072, 0081, 0084, 0134, 0135, 0141, 0150, 0162, 0182, 0187, 0199, 0208, 1019, 1033, 1036, 1071, 1077, 1149, 1150
vcr codes 4015, 4032, 4012, 4020, 4052, 4017, 4039

Turn on device that you want to set
Aim remote at the device
Press the device button for the item you wish to program and the LED will blink once
Press and hold the set button unti the LED lights up solid red
Using the number keys, enter the 4 digit code from the list. After you have entered the 4th digit, the LED will turn off, indicating that the code for the device was recognized.
If the device powers off, test the functions for the other buttons (except OK button). If all the functions work, press the OK button to store the code. If the indicator light remains solid red after blinking 3 times the code is incompatable. You then need to restart back on step 2.
Make a note of the correct 4 digit code for future use.

COde search setting is an alternative method to programming your device without using the code list
Turn on the device you want to set
Aim the remote control at the device
Press the decive button for the item you want to program
Press and hold the SET button until the LED light up solid red
Press the MUTE/SEARCH button. The LED will shut off first then light up solid red.
When the device turns off, press the OK button to store this code.

Code Retrieval
Press and hold the device button you want to display on the remote control
Press the NUMBER 1 then count the number of flashes
Press the NUMBER 2 etc
Press the NUMBER 3 ets
Press the NUMBER 4 etc

If the LED light flashes 10 times the number is 0

Jan 23, 2008 | Audio Players & Recorders

Not finding what you are looking for?
Audio Players & Recorders Logo

Related Topics:

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top RCA Audio Players & Recorders Experts

kakima

Level 3 Expert

98694 Answers

The Knight
The Knight

Level 3 Expert

69654 Answers

Gyula Lacz

Level 3 Expert

482 Answers

Are you a RCA Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...