Tip & How-To about D-Link DWL-520 Wireless PCI Wi-Fi Compatible LAN Card(Refurbished) (RDWL520)

ADD 4% boost to your Wireless Network

This is simple and easy. to do grab your wireless adapter. and grab 90cm of very thin copper wire. now wrap the copper wire around your adapter and bang you should have At Lease 4% boost on your Wireless. some people say they got 8% boost but i only get extra 4%

Good luck Enjoy

Posted by on

D-Link DWL-520 Wireless PCI Wi-Fi Compatible LAN Card(Refurbished) (RDWL520) Logo

Related Topics:

Related Questions:

1 Answer

How do I replace bar bolts on mcculloch ms1635


The bar bolts on this saw are fed in through the oil tank. Push out the damaged bolt. wrap a thin piece of wire around the new bolt's threads leaving enough wire to feed through the open hole in the case. Pull the bar bolt through the hole until you can grab with your fingers. Using bar bolt, start pulling the bolt through the hole, add washers and continue to tighten until you seat the bar bolt.

Oct 13, 2014 | Garden

1 Answer

How do I replace a power cord on hoover u6311?


Heat shrink wrap not electrical tape since it can peel away
New cord longer is better in my opinion
Wire cutters
Or Wire extension or splice adapter
If the wire is brown copper use a new copper wire if it is silver aluminum use a new aluminum wire.

Jun 28, 2014 | Bissell 6594 PowerForce Bagless Upright...

1 Answer

I want to replace the cord/plug is it easy?


Malibu power packs are 1-piece units that can't be taken apart.
However you can cut off the cord and leave about 4-6" of cord sticking out, and then splice into the cord that's sticking out.

Usually I buy heavy orange or black extension cord with male-female plugs on each end.
I cut off female end and use that end to splice into the cord that's sticking out.

How to splice wire.
Use knife and slice down the cord lengthwise... just cut through the outer plastic covering.
Pull the outer cover cover back to reveal black and white wires.
Cut off extra cover.
Cut back insulation on each black and white wire.
Now you have 2 black wires and 2 white wires/
Twist together the copper wire on whites and cover with plastic electrician tape.
Do the same with copper wires on blacks.
Now the blacks are joined/ and whites are joined, and each has tape over copper wire.
Wrap black tape around both sets of wires until all the black and white is covered with several wraps of tape.
That's it. Plug it in.

Nov 23, 2010 | Intermatic Malibu 300W Power Pack...

2 Answers

Chamberlain 102-1499A Opens w/ remote. Will not close w/remote.


If when you try to close the door the main light flashes 10 times and the door reverses to the open position you have a door sensor problem. Make sure they are pointed at one another and the small light on each one is lit and not flickering. If you cannot get both lights to come on you have a bad sensor.

Jul 23, 2010 | Sears Craftsman LiftMaster Chamberlain...

1 Answer

My puppy chewed the cord to my dyson, is it easy to fix?


Very easy, if you don't care how pretty it is. All you need is a sharp knife and some electrical tape. Use the knife on each end of the cord to expose 1/2" of copper wiring, twist them together, cover each wire separately with tape, then wrap several turns of tape around the whole thing.

Oct 30, 2009 | Dyson DC17 Animal Bagless Upright Cyclonic...

Not finding what you are looking for?

1,652 people viewed this tip

Ask a Question

Usually answered in minutes!

Top D-Link Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2260 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18389 Answers

Are you a D-Link Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Loading...