Tip & How-To about Lands Phones

Fixing the handset link to base unit of Panasonic KX-TG4500

After the base unit died I was able to restore power by switching out the power adapter of one of the handsets with the one on the base unit. However, when the power was restored to the base, none of the handsets that previously worked were getting a dial tone. I could only use the phone from the base unit. To fix the handsets I first reset the base unit by pressing the reset button with the tip of a pen on the bottom of the base phone then momentarily removed and reinstall the battery on each of the handsets to allow each to reset individually. In doing so, I got the dial tone back on all previously linked handsets without having to reregister them.

Posted by on

Lands Phones Logo

Related Topics:

Related Questions:

0helpful
1answer

repair base unit
Remove all power from the phone., batteries and the AC adapter for about a minute and if there is a reset button on the base reset it then reinsert the batteries (if it has batteries) and restore the 12 volt adapter. If that doesn't work the unit is probably toast and suffered damage from a voltage spike and fried the internal electronics. Good Luck!
Read full answer
Aug 26, 2014 • Lands Phones
0helpful
1answer

Power outage need to reset - blinks "CL"
remove the power adapter and remove the battery from the handset. Now replace the battery and power the base unit , place the handset on the base and select intercom or search remote.
The base unit must automatically set the frequency to mesh with the handset and handshake to connect.
Read full answer
Sep 19, 2011 • GE 25932 Cordless Phone
0helpful
2answers

We have Panasonic KX-TG6531, 4 handset. One unit is not working and shows on the screen: base no power. We lost a brochure for this phone and don't know how need fix this problem. Would you help us, please?
Hi.
Even though You did not say how old these units are.?.this is a specific battery problem...
you can test it..take the other ones battery and replace problem unit's battery you will see that it will work..You can buy new battery at any Super stores.try to take one with warrant on it..
since you stated that you need an operating manual. pls visit the URL below to download one.
Hope this helps! Take care and please Remember to rate/vote and give me
4 Thumbs Up for me to continue for Helping out the Community :)
Thanks

http://phone.manualsonline.com/manuals/mfg/panasonic/kxtg6531.html
Read full answer
Jul 11, 2011 • Panasonic KX-TG4000B 4-LIne Multi-Handset...
0helpful
1answer

How do I deregister my handsets on my VTech 2656
To be able to register your replacement handset, you must de-register all the handsets from the VT2656 base unit.

Follow the steps below to de-register your handset(s) from the VT2656 base:

1. Take out the handset that sits on the base.
2. Unplug power from the base.
3. Hold down PAGE while reconnecting power. When the In Use light blinks, release the PAGE key.
4. Hold down PAGE key for 5 seconds. When the In Use light begins to flash, release the PAGE key.
5. The handset charging light will blink 5 times. Within 5 seconds from when it stops blinking, press PAGE once.

You must register the handset(s) by following the steps below:

1. After charging the handset, remove it from the cradle, the LCD display will read "SEARCHING FOR BASE".
2. Press "NEW" and then enter the 15-digit Base ID code, located on the underside of the VT2656 base unit.
3. Press "OK". The handset will display "PLEASE WAIT!!".
4. Wait approximately 15 seconds. The handset will display "FOUND BASE". If the handset displays "BASE BUSY TRY LATER", this indicates that the system is in use. Wait until the base unit is in the idle (on hook) mode and repeat steps 2-4.
Read full answer
Apr 30, 2010 • Vtech Digital Cordless Telephone VT-2568
0helpful
4answers

Reset base unit of Uniden TRU9485
Uniden TRU9485 (This didn’t work for me but this was the first instruction from Uniden Tech Support)

TO RESET THE BASE UNIT:
Unplug the base unit AC adapter.
Hold down for 15 seconds the DND, * and “menu” soft key (the middle silver soft key under the LCD) while plugging the base unit AC adapter back in.
All the settings should be reset.

Uniden TRU9485 (Worked for me)
ALTERNATE WAY TO RESET THE BASE UNIT:

Unplug the base unit AC adapter.
Hold down for 15 seconds the DELETE KEY (zero with a line through it) while plugging base unit AC adapter back in.
All the settings should be reset.
Read full answer
May 28, 2009 • Uniden Lands Phones
Not finding what you are looking for?

372 views

Ask a Question

Usually answered in minutes!

Popular Questions

MT6225 china mobile drivers

Lands Phones

How to take silent mode

Uniden DECT 2080-5 Quint Phone

Reset password on Samsung SGH-E250

Lands Phones

Unlock 1 GB micro sd memory card of Kingston Made

Lands Phones

Panasonic cordless handsets all say line in use

Uniden Cordless Phone

Top Lands Phones Experts

Cindy Wells

Level 3 Expert

6688 Answers

k24674

Level 3 Expert

8093 Answers

Brad Brown

Level 3 Expert

19187 Answers

Are you a Lands Phone Expert? Answer questions, earn points and help others

Answer questions

Loading...