Tip & How-To about GE Ovens

Ge profile oven probe and bake lighs flash intermittently

 

unscrewed probe housing, insured  black/white wires were secured to connectors and re-installed housing.  ( white wire was not  fully seated into connector Lights no longer flash.

,

Posted by on

Ovens Logo

Related Topics:

Related Questions:

1 Answer

de dietrich oven , panel shows er2


Tools- philips scredriver, Torx screwdriver
Disconnect from the mains. Open the oven door- use a screwdriver to lever the latch up if it's still locked. Unscrew the 2 screws that hold the oven in the carcass. Pull the oven out from the unit about 6" (you don't need to remove it). Undo the 2 torx screws on the top of the oven and push the top cover of the oven back to reveal the electrics. On the left hand side you'll see a black plate with a reddy brown actuator and a switch. Remove the black plate by taking out the 2 torx screws from the left hand side of the oven. Unclip the switch from the black plate and push it to one side (you don't need to disconnect the wires). Disconnect the reddy brown actuator wires (red on left, black on right although it doesn't actually matter). Remove the plate complete with actuator. Pull the front of the actuator up and slide out forwards, releasing the whole actuator. Don't lose the spring! The little piston at the front of the actuator should only be sticking out a few mm (about 3-4). If it's sticking out more, then it may be stuck. So...
Seperate the 2 halves of the actuator by twisting the bayonet. The actuator half should have it's piston fully retracted, leaving a little flange sticking out. If it's not fully retracted, the actuator is toast and needs renewing. If it is fully retracted, pull out the 2 black parts and the plunger from the part you twisted off the actuator and make sure they are free and not sticking (this is what was wrong with mine). Reassemble the actuator and clip back into the black plate with the spring behind it. Reconnect the power cables. Install the switch. Install the sub-assembly in the oven. Replace the top cover of the oven. Slide oven back into the unit carcass.
Done!
Thanks

Apr 02, 2012 | Ovens

1 Answer

what does f30 mean on the read out


F30 = Open Probe Connection

1. (F30 or F31) Check resistance at room temperature & compare to *RTD Sensor resistance chart. If resistance does not match the RTD chart replace RTD Sensor Probe. Check Sensor wiring harness between EOC & Sensor Probe connector.

2. (F30 or F31) Check resistance at room temperature, if less than 500 ohms, replace *RTD Sensor Probe. Check for shorted Sensor Probe harness between EOC & Probe connector.

Hope helps.

Apr 25, 2011 | Frigidaire 30" Self-Cleaning Freestanding...

1 Answer

New Wall Oven wiring


on a 220v unit you dont use the 110 ,,, connect the red and black as power and the white as ground / larry

Dec 12, 2008 | GE Monogram® ZET3038 Dual Single Oven

2 Answers

moffat oven


U need to open/unscrew back and look at bottom connections to the left ( looking from the back) Earth green and yellow- Blue is neutral and Brown is live you probably need electrical female spade connectors for your end of the 'hard' wire !!

Jun 07, 2008 | Jenn-Air JJW8330D Electric Single Oven

Not finding what you are looking for?

1,649 people viewed this tip

Ask a Question

Usually answered in minutes!

Top GE Ovens Experts

William Miller
William Miller

Level 3 Expert

9086 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a GE Oven Expert? Answer questions, earn points and help others

Answer questions

Loading...