Tip & How-To about Computers & Internet

Electronics in General

This applies to all electronic devices. Unfortunately, there wasn't an option listed for it. Make sure ALL cables are plugged in correctly.

Posted by on

Computers & Internet Logo

Related Topics:

Related Questions:

1 Answer

I have no spark on an 86 kx125 upon reassembly.


Hi, Kurt and Tammy some of the following may not apply as this directed mainly towards Harleys what you need is a wiring diagram for your bike which is in the free service manual listed below it sounds like you may have a pinched wire or faulty wire connector or not wired correctly in the ignition circuit, if you have a CKP sensor it needs compression to send the correct signal to the ICM/ECM, make sure both spark plugs are in heads and use a grounded third plug to check for spark or hold spark plug cable close to spark plug in the head. If still not getting spark the usual suspects are:
1. Fouled spark plugs.
2. Discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
3. Loose connection at ignition coil or plug between ignition sensor and module.
4. Spark plug cables in bad condition, shorting / leaking, spark plug cable connections loose.
5. Faulty ignition coil or ignition / electronic module
6. Failed CKP, CMP, or BAS sensor.
7. Faulty ignition switch.
8. Security alarm failing to disarm needs reset
For more information about your issue, please visit the websites below, and for specific information or questions, please feel free to contact me at xlch@mail.com. Good luck and have a nice day.
http://vermijsmotorsport.nl/manuals/kx125250-030408.pdf
Kawasaki 1986 Kx125 e1 Kx125 parts lists
http://www.kawasaki-techinfo.net/searchOM.php?view_lang=EN&spec=OC&book_no=&lang_code

Dec 01, 2015 | Motorcycles

1 Answer

hi how do I get surround sound coming from my tv


A Samsung home theatre system can make watching movies at home like going to the theater. Proper setup is essential to get the full benefit of the Samsung system, which is available in 5.1 and 7.1 channel surround sound configurations.
Typically the final step in setting up any home theater is connecting your TV to your system.
Like most home theatre systems, your Samsung home theater receiver will allow you to plug all of your components into it, meaning you only have to run a few cables to connect your television to your system.
Make sure your playback devices are properly connected to your receiver.
Whatever playback devices you use, make sure they are plugged into the appropriate inputs on your receiver.
DVD and Blu-ray players, satellite boxes and cable boxes should all be plugged into video inputs, and CD players should be plugged into audio inputs.
Your receiver will have labels on the back panel indicating into which input you should plug your devices.

Connect the video out to your TV's video input. Make sure you use the correct cable to make the connection. For newer receivers, the connection will likely be either HDMI or component.
If your receiver has an HDMI output, use an HDMI cable to connect the receiver to the HDMI input on your TV.
If your receiver uses a component output, use a component cable to connect your receiver to the component input on your TV.


Connect the audio output of your TV to one of the audio inputs on your Samsung receiver if you want to output your television's audio through your home theatre system.
Most recent TVs will either use an optical cable or a digital coaxial cable to connect to the receiver, allowing you 5.1 channel surround from your television.
If you have an older set, you will likely have to use standard RCA cables.


Turn on your receiver and press the "Setup/Menu" button on your receiver's remote.
When "Input" appears on the display, press the right arrow key on your remote to select TV from the list.


After selecting TV, press the up or down arrow keys on your remote to select the audio input jack into which you have plugged your TV's audio cable.
Press the "Exit" button on your remote to exit the setup menu and lock in the settings.


Samsung home theatre system owners guide download
http://downloadcenter.samsung.com/content/UM/200903/20090327091825515/HT-AS730S-XAA.pdfalso
If you're not an electronics junkie, hooking up your surround sound can seem daunting.
There are so many wires and settings that it's understandable why some people might rather pay someone else to do it for them.
But you can do it yourself as long as you make sure the speakers are positioned correctly; the wires are not only plugged in all the way, but plugged into the right places; and the settings on your television and amplifier are set up correctly.

Check to make sure your surround-sound speakers are correctly installed.
Locate the test function on your surround-sound remote control or amplifier panel to do this.
You will know your speakers are hooked up if sound comes out of each speaker during the test.
Make sure your audio cables are hooked up properly.
Make sure the audio cables running from your television to your amplifier are plugged in correctly. The red and white wires should be plugged into the "Audio Out" spot on the back of your television.
Those same red and white audio wires should be plugged into one of the "Audio Input" spaces on the back of your amplifier.

Turn on your television.
Locate the "Menu" button on either your television remote or your television set.
Scroll through your options until you find "Audio Mode" or a similar naming convention.
Select it.
Scroll through your options until you find "Digital Audio Out," or a similar naming convention. Choose it.
Scroll through your options until you find "Dolby Digital Out." Select that option.
Power your surround-sound system on.
Make sure you have the correct audio input selected.
After the correct audio input is selected, make sure you actually have the Dolby Digital aspect of your surround sound system turned on.
The default for most surround-sound systems is the standard two-channel, stereo output.
Set up a home theater
http://www.cnet.com/1991-7386_1-6214422-7.html

Aug 07, 2013 | Samsung Ht-E355 330W 5.1 Channel Home...

1 Answer

Hey, my name is Wesley Murphy and I'm having trouble with our Netgear g54 wireless router. We just got a lap-top and we're trying to get wireless set up on it. We do have internet, that isn't the problem. When we hook the cable straight up to the lap-top from the modem, it works fine, but if we plug it up to the router, it says no internet connection. We've tried everything and still haven't found any answers. We would really like some help with this. When I tried to download the CD it asked for an IP address, subnet mask . . . Etc . . . I have no idea what to do. Please help!


  1. Log in to your NETGEAR router by browsing to http://www.routerlogin.net or http://www.routerlogin.com. Enter the username (admin) and password. By default, the password is password or 1234 unless it has already been changed.
  2. From the left-hand navigation menu of the Router Manager, select Set Up > Wireless Settings.

3. From the center screen, select your encryption type from under the Security Options heading.

    • If the wireless network passphrase is visible, review it and use it to log devices onto your network.
    • If it is not visible, you can change your wireless passphrase; however, changing the passphrase will cause you to lose your wireless connection. Connect your computer to the router with an Ethernet cable before entering a new passphrase into the text box and clicking Apply.
If you cannot log into your router:

Unfortunately, there is no way to recover a lost or forgotten password from a router or access point; you will need to reset the device to factory defaults. However, once the device is reset to factory defaults, you can use the default username ("admin") and password (either "password" or "1234" depending on your router) to reconfigure your router settings.


you might have put in the wrong password or user id check to make sure you have put these in correctly first make sure the caps lock is on/off what ever applies to your user and password id that you provided to your ISP
also
make sure your routers settings are correct ie:password user name,firewall settings to allow your internet to connect also test the lead/s whether usb or ethernet you might check your modem first to make sure that you are getting a connection

Unfortunately, there is no way to recover a lost or forgotten password from a router or access point; you will need to reset the device to factory defaults. However, once the device is reset to factory defaults, you can use the default username ("admin") and password (either "password" or "1234" depending on your router) to reconfigure your router settings.

or

if there is a small hole in the front or back of the router push a hair pin in to reset to factory settings

hope this helps

last resort ring your ISP internet sevice provider get them to check your modem for internet access online

hope this helps


NOTE: Restoring factory defaults on a device will erase any customizations you have made. You will lose any configurations saved to the device!

See the following articles for more information:



hope this helps




Feb 10, 2011 | Computers & Internet

1 Answer

sd card reader stopped


Click the START MENU. then click CONTROL PANEL. In the CONTROL PANEL, locate the link PERFORMANCE AND MAINTENANCE. In the PERFORMANCE AND MAINTENANCE options, click ADMINISTRATIVE TOOLS. Application icons will appear. Double click the SERVICES ICON. In this section, a list to the lest will appear. Double click the option SERVICES AND APPLICATIONS. In the window, a list will appear with services that your computer provides. Scroll down the list until you find Plug and Play Devices, Application Management, Smart card reader, as well as other services your computer may have that involve this service. Once you have located these services, individually RIGHT CLICK each one, click PROPERTIES. Here you will see a DROP MENU BOX. In the DROP MENU BOX, Make sure the device is set to AUTOMATIC, THEN CLICK APPLY, AND START THE SERVICE. In some cases services will not be able to START due to dependency programs being disabled or in STOP MODE. While being in the PROPERTIES of the service, click on the DEPENDENCIES TAB. It will show a list of the programs that is SERVICE depends on to run correctly. Locate that program in the list of services, and follow the above steps. After you have completed these tasks, right click your desktop and click REFRESH. If these options do not work, you may need to download a driver for your SD card.

Nov 23, 2010 | Fujitsu Siemens LifeBook E8020 Notebook

2 Answers

no scan options.


HI,
this is a very normal problem with this printer..do one thing unplug the USB cable from the printer..then if its not working go unplug the USB cable..insert the CD go to my computer..right click on the cd icon explore>>util>>ccc>>uninstall l2..after that restart the system...do a complete installation..issue will be resolved...

Jan 21, 2010 | HP OfficeJet J4580 All-In-One Laser...

Not finding what you are looking for?

474 people viewed this tip

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

kakima

Level 3 Expert

102366 Answers

David Payne
David Payne

Level 3 Expert

14162 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Loading...