20 Most Recent Acer Aspire 6920 Notebook PC - Page 7 Questions & Answers

Hi, please follow the steps in the same order as mentioned

1) Uninstall the web Cam Driver, Camera Capture application and Messenger. Restart the Computer.
2) Install the Camera Driver and Camera Capture application.Restart the Computer.
3) Now install the Messenger. This should resolve the issue.

first thing to check is if you have a USB drive (or thumb drive) plugged in. This often creates an issue with booting. If you do not then unfortunately you have a hard drive issue that may be major, but may be minor. Your best bet is to find a local support person, if you send it back to the manufacturer they may just wipe it and reload. This issue may be physical or created by a virus. Hope things work out I’m happy to help further over the phone at https://www.6ya.com/expert/thomas_b83e841f114394f4

I think I have managed to solve this problem

POWER ON THE LAPTOP

whilst its booting up, you can use the FOLLOWING KEYS TO see picture on the screen:

FN + F6

Whilst its booting, also HIT F2, once your in the bios

Go to:

EXIT > LOAD SETUP DEFAULTS

EXIT SAVING CHANGES > SELECT YES

It should then reboot and ... now its working...SO FAR.

After doing this, the screen stays on, operating system loads up fine.

And I have done approx 10 restarts and also approx 5 power downs and then power on.

Hope this helps

1.Remove ,the battery and adopter from your machine.
2.And then press the power button form 36 Second.
3.And then refix your battery and adopter to your machine.
4.boot your system

1.first Instal the E-power management to your machine.(Didn't had means kindly download the application from our website www.acer.co.in.
2.fully charge your battery till 100% without any interption
3.now you work with your laptop untll it would be the 0%.
4.Kindly repeat the steps four times.
5.After that you Defently feel,your battery backup will increase.

I recommend you to uninstall and reinstall the touchpad drivers from Device Manager.
Press Windows Key and R key.
Type devmgmt.msc and click on OK.
In the Device Manager expand Mouse and other pointing devices.
Right click on touchpad and select Uninstall.
Right click on the touchpad now and select scan for hardware changes.
You can even try to reinstall the new touchpad drivers for your notebook model from acer support website.
For Rundll has stopped working, follow the steps in the below weblink:
http://www.registryrepairsolutions.com/rundll32-has-stopped-working.html

Hi

It could be on the far right hand side of your key board there are a few keys running up from the top right of the keyboard down to the bottom right of the key board possibly the 2nd one down it enables or disables the wireless communications

Please follow the diagnosis outlined in this article to check whether the backlight lamp or the inverter board are the root cause of the problem or not:
http://www.fixya.com/support/r6430776-troubleshooting_laptop_power_failures

If you connect the external monitor & nothing is displayed on it, then this means that both the backlight lamp & the inverter board are fine. The main indicators in these cases are the sound, and the hard drive LED on the laptop case. If the laptop sounds just like it always does for a minute or two after being turned on, it means it's going ahead and booting the operating system, but the video processor or part of the motherboard circuit for video output has failed. If the laptop just sits there and beeps when you turn it on, or if you hear the fan but not the hard drive chuckling with its active LED flashing away, it means the laptop isn't getting as far as trying to boot the operating system. While this could be due to any number of hardware problems, the most common and easiest to
troubleshoot or repair is RAM failure. If your laptop has two RAM modules installed, try booting with just one and then the other in the primary slot. If your laptop only has one RAM module, you might consider buying one online from a site with a good memory selector, like Crucial.com

Per these pages:
http://www.theacerguy.com/forum/topic/quit-acer-arcade-deluxe
http://www.theacerguy.com/forum/topic/acer-arcade-deluxe-loading-on-startup-cant-get-to-windows
This one even tells you how to disable it in windows start up.
http://www.cybertechhelp.com/forums/showthread.php?t=182345

it says to make sure "HOLD" button is not turned on when shuting laptop down otherwise it will do what yours is doing. They are also talking about going in to safe mode and taking it out of start up. Just read the posts and you might be able to get rid of it. The one i found was towards the bottom.

Good luck.

You said you rebooted the system or reinstall the Operating System?

Are you using IE 8? IF you are, remove it and install IE 7 and it should work. Thanks.

Hi. Try to perfrom power drain to your netbook. Take out the battery then unplugged the power adapter. Press and hold the power button for 30 secs. Put everything back in then turn on the computer. If same problem will happen then you need to contact ACER and have your computer srviced for LCD problem.

That indicator is not the Power one, is the "plugged in" one. I also own an Aspire so I know this.

OS corrupt...reinstall OS
need help to do that pls revert back...
regards...

First of all, you need to make sure your power adapter is providing enough power to both run the laptop & charge the battery. A very good way to do this is to compare your laptop voltage & ampere requirements (written on a sticker on the bottom of the laptop) with the voltage & ampere ratings of the power adapter. Voltages should be the same, or the power adapter's voltage about up to 0.5 volts more than the laptop's voltage rating. Amperage of the power adapter should be at least equal to or greater than the laptop's rating. It should never be less than the laptop's rating, or else the power adapter will be providing insufficient amperes to charge the battery. Of course, the power adapter's nominal amperage might be ok, but it degraded on usage. You can verify this by testing using a good or new power adapter.
If the battery did not charge using the new power adapter, take the battery off the laptop, & using a dry tooth brush, scrub in between the fins of the battery connector on the motherboard & on the battery it self, then put the battery back into the laptop & try again.
If this still did not resolve the problem, then the battery itself could be bad. Try it on another laptop, or try a good or new battery in your laptop.
If this did not work, there might be a possibility that the charging circuitry on the laptop's motherboard is defective & needs servicing. In order to do this, the laptop needs to be disassembled & the motherboard checked for defective/burned out components in the area near the DC jack. Any defective/burned out components found should be replaced, or you might need to replace the laptop's motherboard altogether

ok what you need to do is go to the acer site and reinstall the drivers that are related to those programs and you should be fine

First of all, you need to make sure your power adapter is providing enough power to both run the laptop & charge the battery. A very good way to do this is to compare your laptop voltage & ampere requirements (written on a sticker on the bottom of the laptop) with the voltage & ampere ratings of the power adapter. Voltages should be the same, or the power adapter's voltage about up to 0.5 volts more than the laptop's voltage rating. Amperage of the power adapter should be at least equal to or greater than the laptop's rating. It should never be less than the laptop's rating, or else the power adapter will be providing insufficient amperes to charge the battery. Of course, the power adapter's nominal amperage might be ok, but it degraded on usage. You can verify this by testing using a good or new power adapter.
If the battery did not charge using the new power adapter, take the battery off the laptop, & using a dry tooth brush, scrub in between the fins of the battery connector on the motherboard & on the battery it self, then put the battery back into the laptop & try again.
If this still did not resolve the problem, then the battery itself could be bad. Try it on another laptop, or try a good or new battery in your laptop.
If this did not work, there might be a possibility that the charging circuitry on the laptop's motherboard is defective & needs servicing. In order to do this, the laptop needs to be disassembled & the motherboard checked for defective/burned out components in the area near the DC jack. Any defective/burned out components found should be replaced, or you might need to replace the laptop's motherboard altogether.

Once you enter the setup and it loads the entire program, then you need to press the R key, which is for repairing the windows installation. This action will take you to the dos mode where further processing will be done. In the dos mode, system will ask you about installation place. Most of the people install their operating system in the C drive, which comes at number 1 option, so you need to press option 1. However, if you have so many partitions or you have installed the operating system then you need to choose the option according to your drive name. Here you need to enter your password as well, but if you have not set any password then you can simply press enter.
*Then there will be a c:\WINDOWS> command in a dos mode where you need to write, "Copy d:\i386\ntldr c:\windows. However, if you have different place of your installed operating system then you will write the address of that drive. This is the whole process and now you can eject the cd and can press exit to restart the system. Now this process will copy the correct NTLDR file from installation disk to your hard drive by making your system in the working condition.
Remember to fix your Windows registry with Reg In Out Registry Cleaner and PC Optimizer

u may have registry errors uninstall them and run registry cleaner reg in out and then re install them

Symptoms u have identifies are most probably linked to registry errors on ur computer it is wise to run? a registry repair scan with reg in out? registry cleaner....

Try attaching an external monitor to the laptop & see if you could get any display on it. If this is successful, then you might have either a faulty LCD cable or screen inverter board.
The LCD cable transfers data signal from the motherboard & video card to the LCD screen. It also supplies high voltage DC power to the screen inverter board. The screen inverter board works as a power supply for the backlight lamp mounted inside the LCD screen. It converts low voltage DC power to high voltage AC power needed for the backlight lamp.