20 Most Recent Husqvarna "Chain Saw - 16" Bar, 3 Hp Questions & Answers


Did anyone ever think about looking on ebay for this tool? I payed .99 for one, free shipping. It's a lot easier than trying to rig up a home made tool.

Husqvarna "Chain... | Answered on Feb 12, 2018


Forget checking the spark by grounding the plug to the engine. This is both dangerous and does not tell if you have enough spark under compression.
Start by performing a secondary compression check, without proper secondary compression, the unit will not start. You need between 115 - 165 psi.
If compression is good, check the spark with an inline spark tester. Set the gap on the tester at 6mm. If you have a blue / white spark, ignition is good. Make sure the ignition is gapped .20" from the flywheel, more or less will retard or advance the timing of the saw. Make absolutely sure you have the manufacturer's recommended spark plug. If it calls for a resistor plug, it MUST use a resistor plug to operate properly.
If you have compression and spark, check fuel supply. Rebuilding modern carburetors is not recommended. They have very small fuel flow holes (due to emission) Replacement carbs can be purchased for under $100.

Husqvarna "Chain... | Answered on Mar 09, 2017


I would say yes the coil is bad, they do work off speed of rotation, however there is a limit to how fast you can phisicaly crank the engine by hand, the coil is part number 544018401, check out the web for sellers of this component.

Husqvarna "Chain... | Answered on Dec 07, 2016


if you mean where the chain oil lube goes then you could have a fire if any sparks occure ! If its where a seperate 2stroke oil feed should be then you will not lubricate the engine internals and sieze the engine ! Just drain out and fill with oil , 2stroke will need to be bled on the side of oil pump !

Husqvarna "Chain... | Answered on Mar 06, 2016


Get Chain lube for the chain oiler. Naturally, husqvarna recommends that you use "genuine husqvarna" oil for your mixture, I recommend a quality oil, doesn't have to be husky. Husqvarna recommends a 50:1 ratio, other manufacturers, of vertually all 2 cycle power equiptment use a 40:1 ratio. This mixture is slightly richer, but will not hurt your chainsaw. May produce a bit more smoke. Not sure what a 34 husky is...neither is Husqvarna, I visited the website and even tried to download a manual. Looked at every husky model, no 34.

Husqvarna "Chain... | Answered on Feb 28, 2016


If the saw has good compression and spark (check them with proper gauges) check the fuel lines and fuel filter. If this all checks out, then the issue is probably the carburetor itself.

Husqvarna "Chain... | Answered on Feb 03, 2016


You will need to double check your numbers. This number does not appear to be either a serial number or product number.

Husqvarna "Chain... | Answered on Feb 03, 2016


The compression should be between 115 lbs and 145 lbs

Husqvarna "Chain... | Answered on Jan 15, 2016


To remove the cover you must open the chainbrake. Pull the chainbrake lever back towards the operator until it "pops". Then the side cover will slip off of the saw.

Husqvarna "Chain... | Answered on Jan 15, 2016


Take the old chain to a servicing saw dealer that can cut and make up one to fit nearly any saw made. Plus, they will usually give you good tips on maintaining the new chain as well. Hope this helps!

Husqvarna "Chain... | Answered on Nov 29, 2015


carb needs cleaning, rebuilt or replaced. Take off and soak in carb cleaner for a day or so and blow out all orifices with shop air. if this does not fix then probably needs rebuilt or replaced.

Husqvarna "Chain... | Answered on Nov 29, 2015


That metal band you see which is preventing you from putting on the cover is part of the chain break mechanism. You were suppose to disengage the break before taking off the cover (I did the same thing). To get it back together you need to disengage the break by a tricky procedure and that will make the band diameter larger so it fits over the clutch. To force the band open, you need to first place the cover over the two bolts that hold the bar. As you already know, the back of the cover will not be able to fit over the clutch. Now in this angled position, bend (force) the break lever down (gray thing on top) until you can force together the sproket in the cover onto the mating pastic fitting built into the break lever. Now you can use the break lever to force down the internal spring and open the metal band. That will expand the stainless steel band and it will fit around the clutch. If you now push down on the back of the cover it will snap in over the clutch. Once you see how it is done, it is not so hard, but it is tricky because you are forcing some of the parts slightly out of position to get it back together. .

Husqvarna "Chain... | Answered on May 11, 2015


use a hooked rod to snag the oil feed line and filter.

Husqvarna "Chain... | Answered on Mar 07, 2015


Item 10 in the following is where your tank is.

25414748-3ltgkmdacdwnz4x0o5uk2bdr-5-0.png

Husqvarna "Chain... | Answered on Feb 11, 2015


Sounds like a carb problem. My 310 stihl did the same thing. Rebuilt the carb and now it will cut the gates of the hinges off of H**L

Husqvarna "Chain... | Answered on Aug 27, 2014


Adjust the Low idle screw so that it doesn't die out. On most saws, to adjust the idle, look for an opening that has an L next to it (there is also one for high idle speed with an H next to it). Use a small screwdriver, and be careful--many of the idle adjustment screws are plastic so you don't want to strip it.

Husqvarna "Chain... | Answered on Aug 27, 2014


Have you checked the throttle is returning to tickover on the carb ? cable sticking ?
If it is on tickover and still high reving then you could have an air leak after the carb , check the intake manifold , crank seals could be worn and this will let the engine rev by its self ! fuel mixture correct as if its 2stroke a lean mix can do this as well ! ??

Husqvarna "Chain... | Answered on Aug 15, 2014

Not finding what you are looking for?
Husqvarna "Chain Saw - 16" Bar, 3 Hp Logo

581 questions posted

Ask a Question

Usually answered in minutes!

Top Husqvarna Garden Experts

J. Bradshaw

Level 2 Expert

121 Answers

Jay Finke
Jay Finke

Level 3 Expert

1389 Answers

lnbn1975

Level 2 Expert

204 Answers

Are you a Husqvarna Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Husqvarna Garden

  • Husqvarna Garden

Most Popular Question

need know oil gas mixture husqvarna

  • Garden
Loading...