Top 20 Polycom Small ClassStation VSX 8000 (223022120001) Questions & Answers

This worked for me thank you very much

try increasing the volume using the remote. Also have you connected external speakers?

Let me know.

Power on unit, press and hold * key on remote takes a few minutes but spinning polycom logo will appeara and a minute or two after that the menu screen comes up. Main output is configured for S-video, your seeing a 2nd monitor output, doing above will switch the VGA to be main output.

Port Openings!! Check our website at www.vuports.com ... Look under the rental tab and at the bottom for a list of all port opening.s DAVID

Constant red means it is set and ready to record messages after x amount of rings. Flashing red means you have a message. Please always include the model number is such questions and I can find you a manual. Polycom has lots! https://www.google.com/search?q=Polycom+phone+manual ..

hello This is not a dialing but trying to connect to the IP address setup in the system. Start editing the IP address giving the one that you would have already allocated to the device in the Router (i.e. 192.168.1.99) and then reboot it. It should connect then automatically. Best regards

try this on the manual: https://www.google.it/url?sa=t&rct=j&q=&esrc=s&source=web&cd=3&cad=rja&uact=8&ved=0CC4QFjAC&url=http%3A%2F%2Fsupport.polycom.com%2Fglobal%2Fdocuments%2Fsupport%2Fsetup_maintenance%2Fproducts%2Fvoice%2Fvortex_ef2280_programming_guide.pdf&ei=Z_j_VNXZH4vlaqq-gdAH&usg=AFQjCNGMJQMh4hSijpy9ic619NkkmlKOPA&bvm=bv.87611401,d.d2s

are you sure this feature is not blocked on your line? check with another phone connected to the same socket if you can dial the same numbers

The easiest way to fix this is to have use TFTPD32 and set the firmware in the default directory so that when the phone boots it gets its DHCP with Option 66 from the machine running TFTPD32 and automatically pulls the firmware

Unless you are good a solder then you probably won't be able to do it. You wolud need to solder a potentiometer inline of the + voltage to the speaker. Or solder one inline with the existing one. Potentiometer = voltage control aka volume control.

HI. sorry to hear that. Well, here's the solution
Settings should be changed, if it did not resolved the issue? check your coverage area and lastly go and seek a technician to have your device check and re evaluate the condition the mouthpiece or earpiece needs to be replace.
Please accept my solution..thanks

You power supply is probably defective

Decrease the mic volume or move the ext. mics further away from the base unit.

Hi there,

Please explain your problem so i can help you.
Thanks

http://www.brennanit.com.au/UserGuides/User%20Guide%20-%20Polycom%20Soundstation2.pdf

Has this been fixed yet?

google speakerphone 210 manual for choices.

Question edited for clarity. Question moved from Video Consoles category. Trying to find a manual. Are you sure that model is correct? Eircom should give you a manual PDF. https://www.google.com/search?q=Eircom+perform+100+manual and https://www.google.com/search?q=Eircom+perform+100 ..

Hello again Mike. and now you are in the category 'Landline Phones;' rather than Cell Phones, so perhaps it is a phone after all. Contact the cellphone carrier, or but a new Landline Phone. ..

Good question but no 'make model (what it is). Base units have an antenna, make sure it is extended. Make sure the batteries in the satellite hand sets are good as they send out the signal to the base unit to be 'in range'. Not sure about the PIN request, refer to the manual. They are all online. Google make model manual ..