Top 20 Fisher and Paykel WA37T26G Top Load Washer Questions & Answers

you drain pump is the problem,replace it as it is shorting out

to work out the fault code go from right to left far right light is 1 the next is 2 next is 4 then 8, then 16,32,64,128. add up which lights correspond to your machine and then you can google that code and find what your problem is

it will be the pump. just check again where you did last time. there may be something in the hose, coins can get stuck, and lint. check also the pump is not getting very hot.

Does the Machine fill up with water properly sounds to me like the fill sensor is stuffed or an inlet valve issue . Try checking the level of your machine some will stop half way through a load because the machine out of balance switch is stuck on.

check user manual. or go online for customer service. They should have someone that can help.

It sounds like the pump has went bad & also taken out the main board. Common fault is pump.

top loader ? if so burnt out pump if gd blown main computer module

This is the user manual. http://www.fisherpaykel.com/vault/pdfs//pdf_usecares/4112_US_Ecosmart_Washer_EN_FR_UG_lo_0109.pdf

yes or sometimes it is just not sitting in place correctly

have you got the hot water pipe on? the water can sometimes flow back out this valve if it is not plugged. has it been serviced recently? there is a pressure pipe that attaches to the side of the bowl, and a pump that need to be secured or you will get a leak from the bottom. if is has become loud on spin recently, it could be that you have a leak from the main seal, and will need bearings replaced aswell, but that model seems a bit new to need bearings already, but it's not impossible.

you have blown the fuse on the main board. you will need to check short circuits in your pump and motor, and for leaks onto any electrics, and then replace the motor control board (or try to replace fuse on board if other components look fine ie no burn marks)

There is no code for 31. To work out your fault code just add up the lights that are on.

sounds like a valve fault. this fault can be caused by the electronic board not powering the valves also. check power to valves during fill, if power, replace valve. if no power replace board.

250. (11111010) SmartPump Loss Of Sync This fault is normally as a result of the pump not starting. This fault is usually caused by an object that has gotten into the pump, and is either under or on top of the impeller, which is causing the motor to stall when it is trying to start. Primary Source: Pump Stator Windings Open Circuit. Action: Measure the resistances of the pump stator. For more information refer to the AquaSmart service manual. Secondary Source: Pump System. Action: Follow procedures as for Fault Code 249. Tertiary Source: Motor Control Module. Action: Replace Motor Control Module.

Make sure the load is even. If for example heavy towels are on on side and thinner clothes on the other, that would cause the knock.

You will need a technician to fix this,

That sounds like the pump is jammed and did not pump all the water out.

blocked or faulty pump

the lights are a fault code, this will help with diagnosis. check your motor for corrosion.

That is fault code 43 43. (00101011) Phase 1 to 6 - OOB Switch Fault The Motor Controller module has found that the signal returning from the out of balance switch indicates that the switch is permanently on or the harness to it is disconnected. Primary Source: Mechanical. Action: 1) Check that the out of balance switch is free to move. 2) Check that no harnesses are blocking switch movement. 3) Check that the switch operates correctly when activated. Replace the switch if suspect. 4) If the out of balance micro switch shows signs of corrosion, replace the switch and switch harness, and fit a condensation kit to the console area if not incorporated in the top deck. 5) Check the level of the machine and also the bias spring. Secondary Source: Wiring. Action: Check the harness to the switch is connected correctly. The terminals should be connected to the normally closed position. If the harness terminals show signs of corrosion, then fit a new harness.