Top 20 Smeg STA8743U Stainless Steel 24 in. Built-in Dishwasher Questions & Answers

Pull it out and tip it on its front and you should be able to work from underneath, or remove the side panel. This appears to be an Australian model. We are in North America, so this link should work better for you. https://www.google.com/search?q=smeg+dwau6214x+drain+hose+replacement ..

Question moved from Cars and Trucks category. It may be that the water inlet valve that has failed, but it could also be that the main control board has failed. Due to the cost of boards, I would suggest you get professional diagnosis from a Smeg technician.

https://www.hunker.com/13408989/how-to-reset-a-smeg-dishwasher It must be the open and close Quickly that makes this work.

Check the options on the door of dishwasher. Some dishwashers allow you to select wash top rack or bottom or both. Check your settings.

Page 39 and 40 (page numbers, not site numbering) of the manual has your flash codes, but your flashing doesn't exist. Try a reset, disconnect from the mains overnight. If that doesn't fix it, you need a service call. https://www.manuals.ca/smeg/di612e/manual?p=41 ..

This is a possible problem with either the switch that prevents the washer over filling with water during a wash cycle or there is a leak in one of the pipes inside the machine. I would recommend you get an engineeer to look at it as you will need to get inside the machine to repair this.

Water could be leaking under the door as a result of sealing tape failure.

Disconnect from mains power completely for 1 hour. https://www.justanswer.co.uk/appliance/dbtzk-smeg-dishwasher-stopped-working-lights.html It appears to be a known issue https://www.google.com/search?q=smeg+dishwasher+DF4SS-1+has+two+flashing+program+lights ..

This is a commercial unit it error codes are different Er 24 Boiler temperature probe Boiler temperature probe disconnected or not working malfunction this is in the user manual

water level sensor bad

Sounds kinda funny but try unplugging they dishwasher for about 3 minutes where there's no power running to it. The plug should be underneath your sink. Then plug it back in and turn it on and see if it will cycle

I would say yes if tripping main fuse box

Sounds like a control board issue? Turn it off I mean at The breaker or unplug it wait about an hour for the board to clear if it doesnt replace board.

float stuck up or bad, water inlet valve and filter bad plugged inlet line. https://www.youtube.com/watch?v=23GgOka30xA https://www.youtube.com/watch?v=-8GiS0EJeQQ https://www.youtube.com/watch?v=vrDSl24vwao https://www.youtube.com/watch?v=YLkM4yHSY_4 https://www.youtube.com/watch?v=PE16m_Tvssg https://www.youtube.com/watch?v=W9TzcrvlFu0 https://www.youtube.com/watch?v=VtRWr78dbJc

The dishwasher is capable of signalling a number of faults through the simultaneous illumination of several indicator lights. When it stops, what light are on?

SOUNDS LIKE ITS HAD A LEAK AND TURNED ON THE ANTI FLOOD PUMP TREVOR, TRY UNPLUGGING AND TILT THE MACHINE TO REMOVE ANY WATER LYING ON THE BASE PLATE

Check your breaker. If not that could be door switch / latch or control board.

Make sure silverware, broken glass, etc isn’t wedged around hinges.

i have had success with dishwashers that have a (frozen) motor this involves 1 turn off electrical supply and or remove plug from receptacle. 2 turn off water supply, usually under sink, hot water side. 3 remove the mounting screws that you can see under the lip of the ledge when dishwasher door is open,once these are removed 4 carefully pull dishwasher out mindful of the hot water supply line that is attached. 5 visually locate the main shaft, use vise-grips to determine if shaft spins freely if not use v_grips to turn shaft two turns or so, check by closing the appliance door and turning power / water back on then try running unit. this technique will work for some, and only if a (frozen) motor is the problem. this is a temp fix but it is better than nothing. thanx good luck.