20 Most Recent Frigidaire GLTF1670A Front Load Washer - Page 6 Questions & Answers


Hi,
When my washer did that, I found that the shocks that hold the tub were bad...

Check out this tip I wrote about the noise and vibration that front load washers can make..

Washer Problems Washer noise when spinning
heatman101

Frigidaire... | Answered on Aug 29, 2010


if it is right after the drain cycle; it then goes into a spin. It then starts to fill with water for the rinse while the tub is still turning. The water entering the tub while the tub is spinning, cleans the tub of soap and the water going through the holes in the tub are causing the noise. It is normal if only in the rinse cycle.

Frigidaire... | Answered on Aug 29, 2010


Make sure you have plenty of well-lit space to work as well as lay out the parts removed. Remove the cabinet top by removing several screws from the rear, slide it back somewhat, then lift up. Remove the back panel by removing screws along the top rear, then lift up. Pull loose the rubber boot (it's glued to the cabinet front opening as well as to the outer drum face) CAREFULLY from the front panel opening. After uncoupling the drum motor, wiring, hoses, and suspension components, lift out the entire outer drum assembly. The case splits after removing a handful of bolts from the split circumference. Remove the large drum pulley and any snap-rings holding the large shaft in place. The inner drum should pull out of the rear case, but leave the bearings and seal in the case. The inner bearing and seal are prone to failure over time. The official fix is to replace the rear case (with new seal and bearings) for some 300 to 400 dollars. We chose to replace the bearing and seal from a local bearing supply house for about $16. It's still working well after over 10 years. Assemble in reverse order. Use 3M automotive trim cement for gluing the rubber boot back to the cabinet front. Hope this helps!

Frigidaire... | Answered on Jul 25, 2010


Remove the back and see if the belt is still in place,the drm is inclosed,unplug before removing back

Frigidaire... | Answered on Jul 08, 2010


clean filter and or pump

Frigidaire... | Answered on Jun 29, 2010


Hi


Thanks for using FixYa. It means the control board has gone bad and required to be replaced. You can order it online from the link---


Frigidaire GLTF1670A Front Load Washer


Please do accept the solution if the issue is resolved or post a comment for further assistance.


Thanks
Rylee

Frigidaire... | Answered on Jun 12, 2010


hello any spin problems can be down to the module board usually sits down the side of the washer got wires coming off it. the transistor burns out on the board it would be better to get a reconditioned board also make sure the washer is not on rinse hold i'e the button not pressed in good luck

regards
shaun

Frigidaire... | Answered on May 29, 2010


Hi,
If you are having a problem with your top load washer then check out this tip...

Washing Machine2_bing.gif does not Pump or Spin
http://www.fixya.com/support/r4617986-washing_machine_not_pump_or_spin

If you are having problems with your front load washing machine2_bing.gif then checkout this tip...

Front Load Washing Machine2_bing.gif not draining and or not spinning
http://www.fixya.com/support/r4784376-front_load_washing_machine_not_draining

heatman101

Frigidaire... | Answered on May 22, 2010


Check to see if drain pump motor is obstructed. It can cause the oddest problems if not working right.

Frigidaire... | Answered on May 18, 2010


You likely have a corroded/broken spinner assembly on the back of the inner tub. If your washer is out of warranty it is usually cost-prohibitive to repair. We usually quote about $350-$400 parts and labor for it. If you can wiggle the inner basket relative to the outer, that confirms a broken spinner.

Frigidaire... | Answered on May 16, 2010


Well I'm not an expert but I have had problems in the past but it was with my top loader washer. Sounds like it could be a number of things: could be the transmission, or could be a switch or an electrical problem (thats the problem with these new digital washers/dryers!). You will definitely have to call a technician unless you can get a manual and try to fix it yourself. Mine is a year old and I purchased some extra insurance for it, like a year or 2 worth when I bought my washer & dryer new. If your washer is less than a year old you can probably get the manufacturer to fix it for free! Good luck!

Frigidaire... | Answered on May 15, 2010


E20 means a pump blockage and can be "easily" fixed at no cost. Here is how.

I tipped the machine back enough to safely lean against the wall, pulled off a few clamps on the coin trap hose. I couldnt get 2 of the clamps off as they were positioned away from me and didnt have the right tools to mess with it in that cramped space. from the main drum drainage i could feel the coin trap/filter and sure enough, it was absolutely disgusting. So in only a month, the lint from our new towels, dog hair, and gobs of dirt we managed to pack that filter, i got it out and cleaned it out, put it all back together and its good as new.

Here is what the trap looks like.

http://www.repairclinic.com/SSPartDetail.aspx?PartID=408212&PPStack=1

Frigidaire... | Answered on May 14, 2010


I have the same issue with the broken spider...in the us and they say it is $300 for labor and $360 for parts. My washer is only 3+ years old...what can I do?

Frigidaire... | Answered on May 04, 2010


The locking mec is jambed or broke easy fix hope this helps

Frigidaire... | Answered on Apr 29, 2010


Hi,
When my washer did that, I found that the shocks that hold the tub were bad...

Check out this tip I wrote about that...

http://www.fixya.com/support/r3663122-washer_problems_washer_noise_when

heatman101

Frigidaire... | Answered on Apr 26, 2010


Remove the drawer by pushing the tab at the top of the drawer and pull it out and check for an obstruction. They regualarly plug up with gummy fabric softenener. Try washing out with hot water and reinstall

Frigidaire... | Answered on Apr 07, 2010


first check that all 4 legs are level,
and if that dosent work check tat the springs are in good order....

Frigidaire... | Answered on Apr 07, 2010


We use 2x ultra ALL due to having allergies in our family. It is free of perfumes and clear of dyes. We only use 1/4 of the cup (or less) that is supplied with soap container and double rinse. That's the great thing about these washers, they use alot less water and don't need the extra soap as well. Even with the double rinse, at the end of the full cycle, we still see an occasional soap bubble near the door. Hope this helps!

Frigidaire... | Answered on Mar 25, 2010

Not finding what you are looking for?
Frigidaire GLTF1670A Front Load Washer Logo

321 questions posted

Ask a Question

Usually answered in minutes!

Top Frigidaire Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

J. Bradshaw

Level 2 Expert

121 Answers

Archie Ferrarini
Archie Ferrarini

Level 3 Expert

869 Answers

Are you a Frigidaire Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Frigidaire Washing Machines

  • Frigidaire Washing Machines

Most Popular Question

fridgidaire glet1041as1 need assembly

  • Washing Machines
Loading...