20 Most Recent Sony DCR-TRV270E Digital-8 Digital Camcorder - Page 5 Questions & Answers

Looks like you need Sony Service :>( https://www.google.com/search?q=sony+Dsr1800.++error+95+714 ..

you can recover videos from hard drive with file recovery software like asoftech data recoveryhttp://www.asoftech.com/adr/

First of all, why did you reset it ? Was there an underlying error you were attempting to correct ? Resetting equipment is not just for playing with, you know. Have you looked up this issue in the manual, or contacted the FAQ section of the Sony website ?

It has possibly a write issue or maybe a bad HDD. Take it to an Authorised Sony Service Department for service.

For the Error: 91:01 in Sony hdr-pj50e, I will suggest to follow the below steps:

·It may be due to flash or battery problem. ·Turn off the camera and then remove the battery. ·Don't put the camera again for about 1 minute. ·Turn the camera on again.

this model has AV connecting interface, use an AV cord u can connect with an AV input TV

open it, clean the dust with air blower, check whether either the capstan motor or drum drive motor is struck, try to loosen it with a plastic lever.

this camcorder is an earlier model thus the zoom control motor could be weak, if so open it and take out the camera section and unscrew the zoom control motor, loosen it, some sort of sticky grease on the worm gear also obstructs, clean it with small brush or cotton bud. then apply a little silicon grease. don't let dust go in.

clean the side and center sensors in the cassette compartment

take it to a repair man. some doors open via a small motor with a rubber belt. these belts tend to break due ware and tear.

Hi there.
Try DVD Santa, get it here >>>>>>

http://www.freedownloadscenter.com/Multimedia_and_Graphics/Video_and_Animation_Tools/dvdSanta.html

Please read the instructions before use

Good luck and thanks for using FixYa!!

You won't be able to do it with just a USB cable You will need an analog-to-digital video converter which will take the analog video signal from the Camcorder, and translate it to a digital signal for the computer via the USB interface.Startech, Dazzle and Roxio are three brandshttps://www.startech.com/AV/Converters/Video/S-Video-Composite-to-USB-Video-Capture-Cable-TWAIN-Mac-Support~SVID2USB23https://www.sony.ca/en/electronics/support/camcorders-tape-camcorders/dcr-trv103/articles/S1F0064Your iLink port is a Firewire interface, so if you have an older Macintosh computer with firewire, you may be able to go from the camera directly to the Mac with the appropriate 4 pin to 6 pin or 4 pin to 9 pin Firewire cable

Thanks for letting us know. Since you have not, in fact, asked a question, we are unable to supply an answer.

Does the laptop recognize the camcorder as a separate drive ?

Nothing wrong with the Canon, but you cannot expect one piece of equipment to play tapes recorded a dozen years ago on equipment of a different make. Your best bet will be to find someone to transfer the tapes to DVD for you.

This information, and much else that is useful, can be found in the 'manual'.

sir, this error code is related with the HDD, please connect with your computer and save all the files in a folder then format the camera using the computer, then ones more format the HDD with your camera. try it, with record.

you can use the tv cable and plug it in the tv and there or take out the disc and put it on your computer and opwn the disc and find a .vob file (make sure to click the one that has more mb/gb

Trying MTS Converter for Mac support convert AVCHD MTS/M2TS to ProRes, AIC, DNXHD MOV etc. for Final Cut Pro, Final Cut Pro X, iMovie, Final Cut Express, Avid Media Composer 6 compatible format on Mac OS X 10.5, 10.6, 10.7 and 10.8

Print from where ? Is the file a PDF file, or from other proprietary software ? Either way, just send it to your printer.