Gaggia Titanium Espresso Machine - Answered Questions & Fixed issues


Look at the sensor for the door to see if there is any broken plastic pieces or perhaps the sensor has come loose and just needs adjusting.

Gaggia Titanium... | Answered on Feb 13, 2018 | 162 views


the steam valve is most likly plugged with sacale or such have you decaled the machine latly may want to start there

Gaggia Titanium... | Answered on Nov 17, 2017 | 653 views


Me too - machine unusable

Gaggia Titanium... | Answered on May 16, 2017 | 1,537 views


Just let it run the cycle,don't press any buttons.
When it runs out of water refill it and let it continue.
I get this problem a lot,

Gaggia Titanium... | Answered on Jan 23, 2017 | 1,266 views


If its is only the rinsing cycle at start up you can go into the menu and turn the rinsing cycle off.
If its the rinsing cycle for the descale, it has to run out of water to finish. Then reprime the machine and it will start to heat again.

Gaggia Titanium... | Answered on Jan 23, 2017 | 1,519 views


All gaggia is now handled by Saeco.
Give them a call

Gaggia Titanium... | Answered on Oct 14, 2016 | 154 views


Well I guess you know the display is burned out, the question is this do they make parts for the appliance, based on my experience the answer is no.

Gaggia Titanium... | Answered on Oct 12, 2016 | 81 views


Check the 2-pole circuit breaker on the left side. You have to remove the back by removing 2 screws. Use a multimeter, test for continuity over both poles.

My ~8 year old Gaggia Titanium Plus was dead one morning.
I checked the circuit breaker and one of the two poles were bad.
I replaced the C.B. and all was fine :-)

Gaggia Titanium... | Answered on Jul 28, 2016 | 125 views


The heating element is shorted out. Contact the manufacturer for a replacement part (if available)

Gaggia Titanium... | Answered on Jun 29, 2016 | 134 views


Have you checked if cock/fried to crunches for grinding?

Gaggia Titanium... | Answered on May 26, 2016 | 116 views


IT LOOKS THAT THE COMPUTER IS TELLING YOU TO CLOSE THE DOOR FERST BEHIND THAT DOOR MAY BE A MICRO SWITCH WICH IS NOT DOING WHAT ITS SUPPOSE TO DO
TRY TO OPEN AND CLOSE MAY BE YOU HAVE TO BE ALITTLE HURDER THEN NORMAL AS THE SWICH MAY BE WEAK. TRY THIS FERST

Gaggia Titanium... | Answered on Mar 15, 2016 | 244 views


not good you need to remove the display and dry it up and see if the contacts are clean and soldered do solder if its ok only clean it with contact cleaner for electronics

Gaggia Titanium... | Answered on Mar 14, 2016 | 220 views


CHECK IF GRINDER IS DOING ITS JOB MAY BE YOU HAVE TO REPLACE . ALSO CHECK SERVICE IT MAY BE THAT THE SENSOR IS NOT SENSING THE BEANS

Gaggia Titanium... | Answered on Mar 08, 2016 | 141 views


Go to whole latte love and view their video on ventillating. There is a pump that comes with the machine that will pump water into your machine.

Gaggia Titanium... | Answered on Feb 01, 2016 | 137 views


try a finer grind coffee , you cant use a "store" grind in a cappuccino machine it requires a much finer grind than that

Gaggia Titanium... | Answered on Jan 28, 2016 | 1,345 views


Not sure it will work for you but Our Bunn has a flex wire to run thru the tube weekly , and if we do not clean that tube it might take 20 minutes to make a pot where when cleaned it does 12 cups in 3 minute

Gaggia Titanium... | Answered on Jan 25, 2016 | 340 views


warm up well before brewing coffee and set the grinder for finer coffee powder

Gaggia Titanium... | Answered on Jan 24, 2016 | 108 views


CoffeeGeek - Coffee: Machines and Brewing Methods, Bunn MCP ...

coffeegeek.com > Discussions > Coffee > Machines

May 17, 2011 - 10 posts - ‎2 authors
Cycled the power, tried again, same problem...this time I cut the pump process .... The power switch was one of the reasons I like the MCP over the MC in general. .... It's definitely NOT a vibe...those are loud and vibrate like crazy, ..... of the noise you hear is that "honking" sound (the high pitched squeal) that ...

Why I Almost Killed Somebody When I Cleaned my Coffee ...

www.pauljenkins.tv/why-i-almost-killed-somebody-when-i-cleaned-my-...

Gaggia Titanium... | Answered on Dec 21, 2015 | 220 views


If you've had the back off it may be this.....there are two grey plastic prongs sticking out of the back of the casing, when you've put it back on they haven't gone into the two lugs that are on the back of the cog, this affects the two cogs lining up.you may have to pull the cog up a little to line them up when you put the back on, the cogs should line up again as long as the prongs have gone into the lugs. Hope this this helps.

Gaggia Titanium... | Answered on Nov 25, 2015 | 215 views

Not finding what you are looking for?
Gaggia Titanium Espresso Machine Logo

703 questions posted

Ask a Question

Usually answered in minutes!

Top Gaggia Coffee Makers & Espresso Machines Experts

Pierre Laplante

Level 3 Expert

2042 Answers

Marvin
Marvin

Level 3 Expert

84949 Answers

Brad Brown

Level 3 Expert

18060 Answers

Are you a Gaggia Coffee Maker and Espresso Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...