20 Most Recent
Questions & Answers
How do i change the mtu setting on my belkin n
You can adjust MTU from within the Belkin Router administrative console. You really should not be changing it unless your current ISP gives you a specific MTU setting, otherwise you could disrupt internet connectivity.
Default IP address: http://192.168.2.1
Default admin username: Administrator
Default admin password: <blank>
Be sure to set a password for your router!
This is the address where you change MTU
Belkin Wireless G User Manual:
Windows Tools to adjust MTU:
on Mar 12, 2019
I have plugged my belkin
VPI and VCI codes are for broadband ADSL connections check this page out
to see the numbers you need to set up, you also have to configure the encapsulation type according to your country's service, the encapsulation type is usually in the same settings page where the VCI and VPI settings are.
on May 20, 2011
HI, iwant to change my
Connect your router to computer with ethernet cable then you can access it with following default link. http://192.168.1.1 or http://192.168.0.1 or http://192.168.15.1 or http://192.168.2.1 If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router. If you are still not able to access router with above ip then you need to RESET it for that press RESET button for 10 seconds it is in back side of router then all settings defaults..Then you can access it with above method. . Then click on wireless->wireless security->WEP security there is code password note down it or enter new password then save setting s and restart router. then you can connect wireless with new password. Let me know if you need further assistance. Thanks for using FixYa.
on May 05, 2011
Finding password for belkin router
do you forget your password or what well try either of thesee. hope it works
on System Settings under Utilities on the left-hand side of the opened
the computer to one of the four LAN ports on the router.
- Open a
web browser on the computer.
the address bar of the web browser, type http://192.168.2.1
Login in the upper right-hand corner of the page. The router does not
ship with a password, so just click Submit.
- You will see a feature
called, "Administrator Password". Type in your current password
Click "Apply Changes". Your new password is now
not forget the new password and keep it somewhere safe.
If you forget your password, you'll be unable to access your router's
settings. If you forget or lose your password, you'll need to perform a hardware reset on the router. This will reset the password to
its default, as well as erase any
and all other settings you may have changed.
on May 01, 2011
Internet tv is asking for
When you purchased the router, you should have configured the wireless interface:
* set a SSID, a "name" for your wireless network,
* an encryption-level. Hint: use WPA or WPA2
* a password for your wireless network.
Do that, and then use the SSID and password on your Internet TV, to connect to your network.
on Apr 12, 2011
Trying to secure wireless network
Welcome to Fixya. If you want to secure the network you all you need to do is to access the router settings page and put a security either WEP, WPA or WPA2 and a Network Key or Passphrase.
To access the router page you need a working computer that is connected to the router. To access the router page just open a browser then type 192.168.2.1, the Default password is blank
Click on Security under Wireless, Select WEP, WPA or WPA2 and personalize a Security Key or Network Key (Passphrase). Security Key serves as a password on the network.
If you have questions please let me know. Thanks for using Fixya.
on Mar 25, 2011
I have one laptop that
You may need to reset your router by pressing the reset button (usually a very small hole in the back) then you can log in using the default password/username.
on Mar 22, 2011
Internet connects, however when we
Is this a cable service?
It is possible you have a bad connection. Either inside the house or outside.
Cable.. You will have a cable modem connected to the cable.
One main thing to do is to re-trim all the ends of the cable at every connection point between the modem and the outside connection. Replace any old connectors or splitters with new ones of correct value. The idea being to remove any oxidation which will impair the signal. If none of this helps, you may need the outside wiring looked at. Your connection service should do this at no charge.
If you have not done so, power off the modem completely, including removing the battery back up.
Wait about 20 seconds. Reinstall battery and power connection. About 20 -30 seconds to reconnect.
"few hours everyday" might indicate a problem outside, (wiring or junction box) possibly warming up in sun and cooling later?
On the PC. Use the connection wizard to "connect to a network". Connect to your own network on every pc you use.
on Feb 21, 2011
Wireless not working
There are many reasons why this might be happening.. You could try the following steps..
1) Disconnect the power from router for a minute and reconnect and check.
2) Try changing the wireless channel and Network name and try re-connecting.
3) Check if there is an firmware update for your product and update if any update is available.
4) If none of the above steps work you will need to reset and re-config your router. ( For that you need the CD given with the router and you will need the ISP settings.)
Hope this helped
on Feb 15, 2011
How do i change NAT
PS3 And XBOX :: BELKIN
Step 1:Connect Modem - Router - Computer (Wired)
Step 2:Open Router Setup by typing http://192.168.2.1 on the address bar of internet explorer
Step 3:On the Left click firewall
Step 4:Leave the Password blank and click submit
Step 5:Disable it and click apply changes
Step 6:Scan and connect in the Xbox/PS3/Wii
Step 7: Get the IP Address of the Xbox/PS3/Wii
Step 8:Open Router Setup in the Computer
Step 9:On the left under Firewall Click DMZ
Step 10:Enable the IP Address of the Xbox/PS3/Wii in it
Step 11:Click Apply Changes
Step 13:On the left Under Utilities click System settings
Step 14:Scroll down to the bottom
Step 15:Enable UPnP
Step 16:Click apply changes
Step 17:Test the connection ,Check the NAT
If working then let me know
If it is still not working
Open Router setup
At the middle Under internet settings check the WAN IP
IF it starts with 192.168. or 172.16 Then you will have to contact your internet service and ask them to bridge the modem
on Jan 22, 2011
No iternet connection for widows7amber light keeps
Do you see the network on the pc you are trying to access the internet from? If yes, then check to make sure the cable is securely connected from the router to the cable/dsl modem. Try to change the cable out completely if you can. You can also try to bypass the router to the computer to make sure you do have a signal coming in for internet. Try to reset the router and reconfigure it. If you on a loptop make sure you have the wireless on, some models you can switch wireless on and off and this will prevent you from accessing the internet.
on Jan 19, 2011
Not finding what you are looking for?