20 Most Recent
Kenmore HE2t 3.7 cu. ft. Front Load Washer - Page 8 Questions & Answers
I have a Kenmore Elite front loader model 42198900 , this morning shut the door ,light stayed on and no power to controls, any ideas
If you have a Kenmore Elite front loader model 42198900 and the door light stays on while the machine has no power to the controls, there are a few potential causes you can investigate:
1. Check the power supply: Make sure the washing machine is properly plugged into an electrical outlet and that the outlet is functioning properly. If the outlet is not working, check the circuit breaker or fuse box to see if a circuit has tripped or blown.
2. Inspect the door lock: The door lock mechanism may be malfunctioning, preventing the machine from turning on. Check to see if the door is closing properly and if the lock is engaging properly. If the lock is faulty, it may need to be replaced.
3. Check the control board: The control board is responsible for sending power to the various components of the washing machine. If the control board is malfunctioning, it can cause issues like a door light staying on but no power to the controls. Check the control board for any signs of damage or wear, and consider having it tested or replaced if necessary.
4. Look for other potential issues: If the above steps do not identify the problem, there may be other issues with the machine that are causing the problem. Consider contacting a professional appliance repair service for further diagnosis and repair.
How to clean Kenmore Elite sm 9711174 washing machine
To clean your Kenmore Elite SM 9711174 washing machine, you can follow these steps:
1. Clean the exterior of the machine: Wipe down the exterior of the washing machine with a damp cloth and mild detergent. Be sure to dry it thoroughly to prevent any water damage.
2. Clean the drum: Mix a solution of 1/4 cup of baking soda and 1/4 cup of water and pour it into the detergent dispenser. Run the machine on the hottest and longest cycle with an extra rinse. This will help to remove any built-up detergent residue or mildew from the drum.
3. Clean the detergent dispenser: Remove the detergent dispenser and soak it in warm, soapy water for 10-15 minutes. Use a soft-bristled brush to scrub away any buildup or debris, and rinse it thoroughly before replacing it.
4. Clean the lint filter: The lint filter is located near the bottom of the machine. Remove it and rinse it under running water to remove any lint or debris. If the filter is particularly dirty, soak it in warm, soapy water for a few minutes before rinsing it.
5. Run a cleaning cycle: Some washing machines have a self-cleaning cycle that you can use to help remove any buildup or mildew. Check the user manual for instructions on how to run a cleaning cycle on your specific machine.
By following these steps, you should be able to clean your Kenmore Elite SM 9711174 washing machine and keep it running smoothly.
Kenmore elite 100 series.. fills with water for wash but drains immediately
If your Kenmore Elite 100 series washing machine is filling with water for the wash cycle but immediately draining without actually washing the clothes, there could be a few potential causes:
1. Faulty or clogged water level pressure switch: The water level pressure switch is responsible for sensing the water level in the tub and signaling the washer to stop filling once the appropriate level is reached. If this switch is faulty or clogged, it may be signaling the washer to drain the water immediately. You may need to replace the pressure switch or clean the hose that connects it to the tub.
2. Clogged drain hose or pump filter: A clogged drain hose or pump filter can prevent the washer from properly draining the water, causing it to immediately drain as soon as it fills. Check for any clogs or blockages in the drain hose or pump filter and clear them if necessary.
3. Broken or faulty drain pump: If the drain pump is broken or not functioning properly, it may not be able to properly drain the water from the washer, causing it to immediately drain. You may need to replace the drain pump if it is broken.
4. Malfunctioning control board: In rare cases, a malfunctioning control board may be causing the washer to immediately drain after filling. If none of the above solutions work, it may be worth having a professional technician inspect and potentially replace the control board.
I have a Kenmore model 110.25132411 in the rinse cycle only water takes a long time to fill. Then it just drains and doesn't spin.
If your Kenmore washing machine is having trouble filling and then drains without spinning during the rinse cycle, there could be a few possible causes.
- Water supply issue: The first thing to check is the water supply. Make sure the water supply valves are fully open and there are no kinks or blockages in the hoses. Also, check the water pressure and make sure it meets the manufacturer's requirements.
- Faulty water inlet valve: The water inlet valve is responsible for controlling the water flow into the washing machine. If the valve is faulty, it may not be allowing enough water to enter the machine, which can cause the filling to take a long time. It could also be stuck in the drain position, causing the machine to drain instead of filling. You may need to replace the water inlet valve.
- Clogged filter screens: If the filter screens in the water inlet valve are clogged with debris or hard water deposits, it can restrict water flow and cause the machine to fill slowly or not at all. Try cleaning the filter screens to see if this improves the water flow.
- Faulty pressure switch: The pressure switch monitors the water level in the washing machine and tells the control board when to start and stop the filling and draining cycles. If the pressure switch is faulty, it may not be sending the correct signals to the control board, which can cause issues with the filling and draining cycles.
If you have checked the water supply and filter screens and they appear to be working correctly, it may be necessary to replace the water inlet valve or pressure switch. If you are not comfortable performing these repairs yourself, it may be best to contact a qualified appliance repair technician to diagnose and fix the problem.
I am looking for a drive belt (?) for my Kenmore top-loading washing machine, Model 110.4563291.
You can obtain a drive belt for your Kenmore top-loading washing machine, Model 110.4563291, from several sources:
- Sears Parts Direct: They offer parts for Kenmore products and can help you find the correct drive belt for your model.
- Local appliance repair shops: They may have the drive belt in stock or can order it for you.
- Online retailers: Such as Amazon or eBay, offer a wide variety of washing machine parts including drive belts.
It's important to note the model number and the type of drive belt you need to ensure you get the correct part.
I have a kenmore model 110,5142510, SER C60420403 water does not come out sounds like motor wants to run but it doesn't do anything
It sounds like there may be an issue with the water inlet valve on your Kenmore washing machine. The water inlet valve controls the flow of water into the washing machine and it could be that it is not opening properly, preventing water from entering the machine. Another possible issue is with the water pressure, the water pressure may be too low.
It could also be a problem with the lid switch, if the lid switch is not functioning properly, the machine will not start. This switch is located inside the washing machine and is activated by the lid. It is designed to prevent the machine from running if the lid is open.
It's also possible that there is a problem with the motor, which is preventing the machine from spinning.
It is recommended that you contact a professional to diagnose and repair the problem as these are complex machine and it's better to be handled by a specialist.
I have an E24 message on my Kenmore dishwasher - model 630.1390
The E24 error code on a Kenmore dishwasher model 630.1390 typically indicates a problem with the drain pump or the drain hose. This can cause the dishwasher to start adding water but then shut off and display the E24 error message.
Here are some steps you can try to fix the issue:
- Check the drain hose for any clogs or blockages. Make sure the hose is not kinked or bent and that it is properly connected to the garbage disposal or drain.
- Inspect the drain pump for any debris or foreign objects. Clean out the pump, if necessary.
- Check the air gap on the dishwasher. Make sure it is not clogged or blocked.
- Inspect the control board and check for any error messages.
- Power off the dishwasher and unplug it for 10 minutes to reset the electronic control board.
- Make sure the dishwasher is level and that the legs are adjusted properly.
If the problem persists even after trying these steps, it might be best to contact a professional technician for further diagnosis and repair.
Kenmore stackable washer/drier. Water doesn't drain out.
Kenmore stackable washer dryer doesn't cycle (doesn't advance to water fill or wash, drain, rinse, spin) (not spinning, draining, filling?) After the video, we learned it was the points in the timer. It wasn't the black "electrical plug", being plugged into. Get your serial number and google Kenmore timer and you can order a replacement timer. Even if you still have someone come out, you've still saved a bunch!.......ps....I had a viewer make a good point!; I obviously didn't have any issues, but obviously be careful with electrical panel and any loose wires!
Not finding what you are looking for?