Whirlpool Ultimate Care II LSQ9549L Top Load Washer - Answered Questions & Fixed issues


Go to www.repairclinic.com and enter LSQ9549LW1. With luck, you will be presented with a list of common replacement parts and may be able to view a generic Whirlpool video showing disassembly.

Whirlpool... | Answered on Dec 09, 2017 | 40 views


most if not all washers have three phase motor fitted for the purpose of the torque that is required but will only run
on three phase electric supply , and so these motors are
externally fitted with capacitor and run on the principle of three phase , but once these capacitors start to brake down the electric motor fail to run .
you may have a capacitor doing down

Whirlpool... | Answered on Nov 25, 2017 | 50 views


Check screens on both hoses and on water valve. Clean as needed. Obviously you need to be sure you have water coming from house source.

Whirlpool... | Answered on Nov 04, 2017 | 66 views


Either the wire going to motor for non working speed is loose or damaged, or motor is bad. It could also possibly be timer not sending power to motor for that speed.

Whirlpool... | Answered on Sep 27, 2017 | 55 views


Defective lid switch is most likely causing problem

Whirlpool... | Answered on Sep 11, 2017 | 206 views


Your timer is causing the problem more than likely, valves , pump motor is working so your timer itself is not change it most of the jobs can be done by the homeowner they are a quick connect disconnect and maybe a screw or a catch holding it just look at it how it attached to the console and reattach it the same way

Whirlpool... | Answered on Aug 12, 2017 | 32 views


more likely from a hose........need lid off and a good torch

cheers

Whirlpool... | Answered on Aug 03, 2017 | 622 views


No spin, or lite spin try these: bare in mind that many times there is no spin it can be due to a clogged water pump so check it for debris and or broken propeller.

Other items to check Using a multi meter check for continuity the door switch, which when bad may not allow agitation or spin. Bare in mind the lid switch assembly can fail either mechanically or electrically.

Check the clutch, brake assembly and transmission, one way to check for slipping is to get under the machine after a spin cycle ( this is if u get a lil spin but not much leaving clothes still wet) mix in a spray bottle a lil water and some dish detergent, then spray it on the clutch assembly ( the metal round pc. Connected to the tranny) if it sizzles and steams up then u know its bad and slipping. Another way to check clutch if u get no spin at all? Is to take it out and use ur hand to try and turn the inner spring assembly pushing it around the inside? If its very easy, it BAD should be hard to push by hand.

Or try the hand test:

If no hammering sound has ever been heard out of this machine, one of the unofficial tests we professional appliantologists will do in the field is called the Hand Test. WARNING:This test is not sanctioned by Whirlpool Corporation; it involves bypassing safety equipment and then putting your hand on and near rotating machinery which could result in injury, dismemberment, disfigurement, disembowelment, mangling, hideous screaming, and a ****** *****. Proceed at your own risk! Have a nice day.

- put the timer on a spin cycle and open the lid- grab the inner basket with maybe 30% to 40% of your hand strength with your left hand
- turn on the machine and bypass the lid switch by depressing the lid switch with a key until the machine begins to spin
- if the clutch is engaging properly, the basket should immediately begin to spin and slip through your hand
- if it takes very little force to stop the tub from spinning, the clutch needs to be replaced.

Next check the motor coupler which engages the tub and tranny to the motor. ( if its bad u usually get no wash or spin or very little of either)

Next if belt driven check for a loose, worn or broken belt. And on some models there is no clutch but rather what is called a splutch. And a MODE shifter. These can go bad and effect the spin cycle.

On some front load models u may need to check the STATOR assembly.
The stator is essentially one half of a motor, it interacts with the tub by creating a strong electro-magnet. If the stator burns out the washer won't spin or agitate. Check the stator for continuity. This part is often misdiagnosed.

Sometimes a no spin machine can be due to a plugged waterpump hose or obstructed water pump propeller. Check these by eye and hand. And in some models check with a meter for continuity and voltage.

LID SWITCH TEST- next step is toremove the cabinetand jumper the lid switch harness (tan to gray). Put the unit in spin and watch the shiny metal clutch disc that is on top of the transmission where the shaft comes out. If the machine starts and runs in spin, check to see if the disc is spinning. If it is, then the problem isnot in the gearcase- look for trouble in theclutch,
basket driveor the tub drive block

If, on the other hand, the disc is NOT spinning, check for a problem withthe motor drive coupleror one of its retainers. This washer doesn't have a belt. Instead, the motor is directly coupled to the gearcase by a drive coupler; that's why it's called a direct drive washer.

Read more:Diagnosing and Repairing Spin and Agitate Problems in a Whirlpool / Kenmore Direct Drive Washer

http://fixitnow.com/wp/2010/07/07/diagnosing-and-repairing-spin-and-agitate-problems-in-a-whirlpool-kenmore-direct-drive-washer/#ixzz3XW7eZwiN
By the way my advice is free cuz God is good!






Diagnosing and Repairing Spin and Agitate Problems in Whirlpool Kenmore...
belt broken beltwasher motor maytag amana-n2one1aiwr4twi02ek2pnwzo-2-0.jpg

clutch spring-n2one1aiwr4twi02ek2pnwzo-2-2.jpg

coupler-n2one1aiwr4twi02ek2pnwzo-2-5.jpg

coupler set up and remove-n2one1aiwr4twi02ek2pnwzo-2-9.jpg

doorswitch bypass-lid-switch-unplug-n2one1aiwr4twi02ek2pnwzo-2-14.jpg

doorswitch lid -n2one1aiwr4twi02ek2pnwzo-2-20.jpg

Whirlpool... | Answered on Mar 24, 2017 | 489 views


You'll have to be a little more specific please. What kind of trap are you thinking of/referring to? Not aware of any type of "trap " on this model. Are you talking about some sort of lint trap? And what problem/s are you having with the washer (like what's it doing or not doing)?

Whirlpool... | Answered on Jul 29, 2016 | 82 views


probably a problem wash engage solenoid underneath or broken drive belt
call an technician in for a proper diagnosis and a quote

Whirlpool... | Answered on Jul 16, 2016 | 61 views


is your outlet pipe tall enough to prevent siphoning .

Whirlpool... | Answered on Apr 01, 2016 | 54 views


replace water inlet valve that your hoses hook to.

Whirlpool... | Answered on Jan 02, 2016 | 289 views


usually take a bunch of screws out and lift it off .

Whirlpool... | Answered on Oct 24, 2015 | 75 views


WHOA turn the water off behind the machine and replace the inlet valve. .

Whirlpool... | Answered on Sep 24, 2015 | 208 views


It sounds like you may have a clogged screen in your water valve. Turn the water off going to the washer and remove one hose at a time from the back of the washer and look inside the body of the water valve, you should see a small metal screen inside the valve, and they should be clear of any debris. If you see any debris built up on the screen, carefully remove the screen, I usually use a small flat blade screwdriver, and then use a small brush, like an old toothbrush, and scrub it under a stream of water in your sink until it is clear of any debris. Carefully put the screen back in and put your hose back on and then turn your water back on and you should be good to go. If you do not have any debris on the screens, then you could have a bad water valve and that would need to be replaced. Hope this helps!

Whirlpool... | Answered on Sep 22, 2015 | 77 views


The selector is the problem source.

Whirlpool... | Answered on Jul 16, 2015 | 73 views


LOUD NOISES IN washing MACHINE;

LOT OF THINGS TO CHECK, THE BELT LOOSE OR WORN, THE CLUTCH, THE TRANNY, THE BEARINGS BOTH TUB SEAL AND BEARING, THE REAR DRUM BEARING, the balance or counter weights.

THE DRIVE PULLEY- If the washer is making a loud noise the drive pulley might be worn out, cracked, loose or bent. Remove the drive pulley and inspect it carefully. If it is damaged or defective replace it.
THE TRANSMISSION, THE MOTOR COUPLER, THE MOTOR DRIVE BEARINGS,
THE DRIVE MOTOR- If the washer is making a loud noise the drive motor bearings may have worn out. Washer motors are normally almost silent when they run. If the motor is run without a belt hooked up to it and it's loud it will have to be replaced.

The drive coupling connects the motor to the transmission and consists of two plastic drive forks with a rubber coupling between them. One of the drive forks is attached to the drive motor shaft and the other is attached to the transmission input shaft. As the motor shaft rotates, the rubber coupling between the drive forks absorbs the torque to prevent the forks from breaking. Normal use will create wear on the coupling and eventually the drive forks may slip and cause a vibrating noise. If the transmission seizes or if the spin basket cannot turn freely, then the coupling may fail and again you may experience a vibrating noise. Most models will require you to remove the cabinet to access the drive coupler. Disconnect power from the appliance before attempting any repairs.


If the washer is making a loud noise the drain pump might be going bad or might have something caught in it. Remove the drain pump from the washer and inspect it carefully. Look for anything that might be caught in it, a piece of wire, plastic, etc. If nothing is wrong with the pump, but it's still noisy it will have to be replaced.

Front load washers often use a self contained electric drain pump and the motor may be worn or damaged and require the complete pump to be replaced. Remove any foreign objects or replace the worn or damaged pump, thencarefully tighten the hose clamps and check for leaks before installing the cabinet or front panel.

All front-load washing machines have shock absorbers that are used to dampen the tub movement in the spin cycle. The shock absorbers or struts are attached to the base frame and to the outer tub and you will need to remove the front panel or the rear panel to access them. When shock absorbers weaken or become damaged, the machine will often make a loud banging sound during the spin cycle and if the symptom is not corrected, can lead to damage of other components. Inspect the shocks for signs of broken attachments, leaked fluids or a weakened dampening action and replace both shocks if worn. Remove power from the appliance before attempting this repair.

Some models of top-load washers use tub dampening straps to cushion the movement of the tub during the spin cycle. There are four straps attached to the top of the tub and to each corner of the cabinet

Also There are four suspension rods that suspend the tub and allow the tub to free float. If the suspension rods are noisy, there will be a squeaking noise during wash. You can fix this by putting bearing (lithium base) grease in the cup that each rod rests in. If it continues to squeal replace all four rods the cups come with the rods, replace them as well.

If your washer has a loud banging noise during spin the balance weight may be loose. This weight is to counter act the weight of the motor so you will find the weight directly behind the motor. Sometimes simply tightening the bolts will fix your issue but if the bolts are stripped out get some bolts slightly longer than the original bolt to allow you to put a locking nut on the bottom side of the mounting plate. If the weight is broken replace it.

Lastly Washer vibration can be caused by a broken counter balance spring. Ur washer may be equipped with one or more counter balance springs which help to absorb the natural movement of the spinning tub. If a counter balance spring fails the tub might lean in one direction more than another and it will shake and cause vibration.







Whirlpool... | Answered on Apr 04, 2015 | 84 views


you are missing a couple letters in model number,here is a link t all the parts for particular washer, Search eReplacementParts com

you can use this cleaner,
25607118-yjo0ud12y22pkmokvfqa1yzz-2-0.png here is the hose,
25607118-yjo0ud12y22pkmokvfqa1yzz-2-2.png

Whirlpool... | Answered on Mar 25, 2015 | 68 views


check the switch for load size,make sure it is on high and see if that works.

Whirlpool... | Answered on Mar 14, 2015 | 46 views

Not finding what you are looking for?
Whirlpool Ultimate Care II LSQ9549L Top Load Washer Logo

2,460 questions posted

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Sal DeAngelo

Level 3 Expert

2333 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...