20 Most Recent Whirlpool Cabrio WTW6600SBK - Page 9 Questions & Answers


Two things to check and try although I'm not a washer repair man or know anything about certain models. >> 1-- To make the job a bit easier find a block of wood like a 2x4 or a 4x4, tilt the washer back and set the front of the washer up on the block or blocks.

Now take off the bottom front panel of the washer. There are a couple of screws at the very bottom that need to be removed. Then tap on the panel while pulling down and it will slide right off.

On the right hand side reach up inside the front panel to the latch assembly. Grab hold of the tab on the bottom of the latch assembly and your door will open.

If your door keeps getting stuck then you may need to replace the door latch assembly.

#2 ---1.Unplug machine
2.remove bottom panel
3.Reach up along the inside of the front panel and locate the bottom of the door latch assembly
4.Located on the bottom of the door latch assembly is a tear dropped shaped tab
5. Gently pull down on the tab about a 1/4 inch or until a click is heard.
.

Whirlpool... | Answered on Jun 07, 2019


Hi Angela, you should contact Whirlpool directly and find out if that is a common complaint. If it's a manufacturing defect they should replace the defective part. Hope that helps.

Whirlpool... | Answered on Jun 04, 2019


Hi Paul, first piece of advice is to make sure the loads of laundry are consistent. A pair of jeans or a bath towel in a load of lighter clothes can cause an off balance condition, causing the machine to constantly try to re balance the load and never reaching high speed spin. Other than that,make sure your spin speed option is set to high. If those don't solve the issue,contact a local repair company to come out and take a look. Hope that helps.

Whirlpool... | Answered on Jun 04, 2019


check there is plenty of water going into the machine if not probably a faulty water solenoid

Whirlpool... | Answered on Jun 02, 2019


Sorry we do not have that kind of info here, contact Whirlpool.

Whirlpool... | Answered on May 31, 2019


Problem with the Whirlpool Shift Actuator. Fault is displayed when the main control cannot determine position of shifter. • Check harness connections from main control to motor and shifter. • Observe shifter operation. Replace the shifter if it is bad.

Whirlpool... | Answered on May 30, 2019


https://www.searspartsdirect.com/washer-repair/error-codes/whirlpool-cabrio-top-load-washer-error-codes.html
Motor Stalled The motor RPS (Rotor Position Sensor) detects no rotation of the drive motor. Unplug the washer. Check to see if the basket spins freely. If not, then examine the drive system and eliminate the cause of friction. If the basket spins freely, check the wire harness connections between the main electronic control board and the motor. If the wire harness connections are okay, check the drive motor. If the motor is defective, replace it.

Whirlpool... | Answered on May 27, 2019


You have to access this dryer through the front. First, unplug the dryer. Next, remove the lower front panel. There are 2 hidden metal spring clips in the seam above the lower front panel and if you slide a flat head screwdriver above these clips you can pry them down and the lower front panel will hinge forward ad down and unclip from the top. Now the fuse is mounted to the top of the blower wheel housing behind the lint filter enclosure. But the fuse stops the motor so that isn't going to be the problem.If the unit is just not heating, look at the heating canister under the drum along the right side. There are 2 small devices attached to the left side of the heating element. Test these 2 parts for continuity and if either are open, replace it. Also test the heating element itself for continuity and if that doesn't have continuity, replace the element.
https://www.justanswer.com/appliance/a78fy-locate-fuses-whirlpool-ultimate-care-ii.html

Whirlpool... | Answered on May 25, 2019


Sounds like the belt under the machine is either broken or off the motor/pulleys. Empty the tub, turn off water, disconnect the power. Pull unit away from wall, tip it back so you can look underneath (Make sure to put blocks under machine so it doesn't fall on your head)Find the old belt to get the size. To replace the belt, put it on the motor pulley, the on the large pulley, then the small one. The motor mount is usually under spring tension.

Whirlpool... | Answered on May 25, 2019

Not finding what you are looking for?
Whirlpool Cabrio WTW6600SBK Logo

74 questions posted

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Marvin
Marvin

Level 3 Expert

84949 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1479 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Cabrio Whirlpool

  • Cabrio Whirlpool

Most Popular Question

whirlpool cabrio error code f51 mean

  • Washing Machines
Loading...