20 Most Recent Lang Manufacturing EHS-APM Electric Oven Questions & Answers


I believe the fan is supposed to rotate one way, then stop and spin the other way, ie. clockwise, then counter clockwise. Did the service guys check this? what service company did you use? You probably already know this but make sure the sides of the pan are NOT touching any of the sides of the oven. I work for a service company myself and I have to say if I got this call and neither of those two things solved it, I would be stumped!

Lang... | Answered on Jun 07, 2010


First off, you will need to have each oven on a dedicated 3phase circuit.Make sure your breaker box can handle an additional 360 amps before you wire anything. You may not be able to use all 3 at once, if the main breaker can't carry the load.

Lang... | Answered on Feb 09, 2010


go to partstown.com the have the manual for your oven in the top right corner

Lang... | Answered on Oct 31, 2009


Hi

You must check the main power wires where they enter the range at the T-block, sometimes they can burn off. Also check house fuses (or breaker) that supplies power to the range. Checking with a volt meter, you should get 240 volts between the black and red main power wires. The range receptacle and power cord can also burn and fail. Also check the screw in fuses, they are usually the 30 amp fuses for the oven. Next is the clock assembly, often these clocks will have the words "push for manual" or "turn for manual", this will put the clock back into the normal operating mode rather than the automatic mode. If all checks ok, you will have to test the selector switch and oven control.

Please do accept the solution if the issue is resolved or else revert for further assistance.

Thanks
Rylee

Lang... | Answered on Sep 10, 2009


Hello, It could be that the EOC is bad but have you checked both sides of the breaker? as you may already know the 220v is on 2 breakers, although you may see the clock still working you still have 120v to the control side, the 120v breaker for the heater side of the cuircuit could have popped...If after checking the breaker you have a full 220 then I would have to say it's going to be a problem with your EOC or high limit if this model has one. Mike

Lang... | Answered on Sep 03, 2009


http://www.langworld.com/lang_cd/Operate%20Manuals/CNVTOVEN/Op%20Convections.pdf
Check out this web site for your manual. The model EHS-APM is not listed but there are other units with multiple programming options. You will have to browse somewhat but what you are looking for is probably there.
Good Luck and hope this helps.

Lang... | Answered on May 23, 2009


If it is a fan assisted oven, and the fan is working, then you need to fit a new oven element.
This is located at the rear of the oven where the fan is. Plz rate my solution.
Thanks.

Lang... | Answered on May 14, 2009


If your model # is ECOH-AP208DR, Electric Half Size Computerized Convection oven, the timer is as follows: 2J-30800-05 Timer Elec. 1hr 24V. Please check the time range of 1 hour and voltage on old timer be insure this is correct.

Lang... | Answered on Apr 30, 2009


WB, Your thermostat is shot and must be replaced. The most difficult part of this job is locating one to replace it with. Have the complete Model and Serial number handy... First, try locally. Call a local Commercial Kitchen repair/parts house. Surely theres one nearby, they work on all McDonalds, Wendy's, Restaraunts, etc... cooking equipment. Second, contact the manufacturer; Star Manufacturing International, Inc. 10 Sunnen Drive St. Louis, MO 63143-3800 Phone (314) 781-2777 (800) 264-7827 Fax (800) 264-6666 After you have it, SHUT OFF THE POWER AT THE BREAKER!!! Now try to turn the unit on to VERIFY you have no power. Then remove the t'stat knob. Now remove the screws holding the control panel in place. Tilt the control panel out toward you. Now you can see the t'stat and see how the sensor bulb is routed. (HINT: Take a piece of paper and draw the back side of the t'stat's wire connection locations and wire colors/numbers, BEFORE removing anything.) Remove the wires and the t'stat and route/wire the new one the same way. Another tip; Be extremely careful with the sensor bulbs capillary tube (the small tube connecting the bulb to the t'stat). NO 90 DEGREE BENDS ALLOWED! It is a hollow tube, if it's piched/kinked you can throw it in the trash and buy yourself a new one. (It came packaged as a coil for a reason) As you uncoil it, go slow and easy.

Lang... | Answered on May 07, 2008


your old jennair is 220 should be three or 4 wires in it red for 1 side of the 220 black for the other side of the 220 white for the bottom of the outlet and if green is there you can hook it with the white wire or just not use it let me know if your colors are different

Ovens | Answered Yesterday


It will be the oven element that has failed, a new one wiil need to be fitted.

It is located at the rear of the oven compartment behind a removeable cover.

I hope this helps.

Ovens | Answered Yesterday

Not finding what you are looking for?
Lang Manufacturing EHS-APM Electric Oven Logo

Popular Tags

25 questions posted

Ask a Question

Usually answered in minutes!

Top Lang Manufacturing Ovens Experts

Dennis Boxerman

Level 3 Expert

1300 Answers

Anthony Ward
Anthony Ward

Level 2 Expert

396 Answers

Tom Chichester

Level 3 Expert

52791 Answers

Are you a Lang Manufacturing Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Lang Manufacturing Ovens

  • Lang Manufacturing Ovens

Most Popular Question

electric oven problems

  • Ovens
Loading...