20 Most Recent Belkin Wireless G Plus MIMO (F5D9230-4) Router (1010835) Questions & Answers


Check for a firmware update and, if that doesn't work, call Belkin and discuss a possible warranty replacement.

I have had nothing but problems with their equipment and do not recommend it.

Belkin Wireless... | Answered on Apr 24, 2017


Once You Connected The Belkin Router With Computer Please Open The Web Browser And Type 192.168.2.1 And Hit Enter .

2- Belkin Router setup Page Or Belkin Dashboard will come up And Now you Can Configure The Settings In your Belkin router .

You can change or setup password as you wish . After setup Your Belkin Router Please Restart Your Router And Computer.
For more visit-
How to Setup Belkin router Install Belkin Wireless router
Good luck.....

Belkin Wireless... | Answered on Apr 21, 2017


this type of problem can be fixed very in simple steps :-
reset the router and install belkin router setup from belkin site
go to wireless settings and setup user name and password
now follow the instractions and try to connect your devices for more assistance contact belkin Services i hope this will help you

Belkin Wireless... | Answered on Apr 21, 2017


IT means that the router has gone defective.

Belkin Wireless... | Answered on Apr 21, 2017


Dony worry just follow these steps.
Restart ur belkin router.
Reset the setting and recomfigure ur router
or click on link
How to Setup Belkin router Install Belkin Wireless router
good luck

Belkin Wireless... | Answered on Apr 21, 2017


try to reset the router...
Restart = take out the power cable and wait for 20 sec than plug it back
  • Restart the modem (cable/dsl modem)
  • Now restart the router and computer also and wait for 2 min .
  • See if this get you belkin wireless router online .
  • for more details click on link
Belkin wireless router is not working Get belkin router setup
good luck

Belkin Wireless... | Answered on Apr 21, 2017


It's much easier to fix belkin router problem with these instructions :-
1. let's say you have a old or new belkin router.
2. Restart your modem or router.
3. plug the router with computer using a eathernet cable.
4. Open the belkin setup page.
For more visit:-
Belkin wireless router is not working Get belkin router setup
I hope this work out.

Belkin Wireless... | Answered on Apr 20, 2017


Oh, I can understand this problem.It's very easy to fix.
Quick Steps to fix this problem :-
> Restart your Belkin router.
> Reset the setting.
>Reconfegure your router.
For more steps you need to visit
Belkin router blinking orange FIX belkin router amber light Issue

Belkin Wireless... | Answered on Apr 20, 2017


Connect one computer directly to the DSL modem using an Ethernet cable. If your DSL service includes a static IP address, then you will need to change the TCP/IP settings on your computer to connect directly to the DSL modem. that the router or other device on your network . For these you need to follow thse steps.
Belkin router blinking orange FIX belkin router amber light Issue

This may help you.

Belkin Wireless... | Answered on Apr 20, 2017


Contact Belkin for Care at 1-800-585-2494 Toll Free:

Belkin Wireless... | Answered on Apr 19, 2017


1 800 2BELKIN x2263

Belkin Wireless... | Answered on Mar 22, 2017


it depends on what you specifically want to password-protect: a. protecting the network from unauthorized users? b. protecting the network's admin interface?
for a. - log into your network's admin interface (usually http://192.168.0.1) - go to the category of wireless security - select the type of network protection you are looking for (strength - i.e. wep, wap, wpa2) and set your password following the steps listed within your router's admin interface...
for b. - log into your network's admin interface (usually http://192.168.0.1) - if you have never done this before, then your username should be filled in as Admin and leave password blank and hit enter.... from there, you are able to change or at least add a password to the interface from unauthorized access (usually under category security)

Belkin Wireless... | Answered on Feb 17, 2017


Access the built-in web-server software "inside" the router, and check the 'WAN' settings.

Contact AT&T, and ask for Technical Support, to verify that their router is working correctly.

Belkin Wireless... | Answered on Dec 30, 2016


maybe instead of nat, set you xbox as a DMZ host. This would be done on the router itself. It will allow the Xbox to bypass the firewall and nat on the router/gateway, and at the same time keep your computer safe.

Belkin Wireless... | Answered on Oct 22, 2016


Under System Settings on the Router: Extend the time of the "Time Out" or inactivity under NAT or, if that option is not available, then turn NAT off.

Belkin Wireless... | Answered on Oct 22, 2016


Normally, routers come with a software wizard that will help you set up your wireless and security settings. If this is not the case, you will need to do it manually.
First, you will need the IP of the router. Sometimes it's listed on the bottom of the device, sometimes it's in the manual, sometimes both. If you still cannot find it, try searching for 'defaul ip for XXXXXXX' where x is your router's modle number.
Then, go into IE (or Firefox, Chrome, Safari etc.) and type the IP into the address bar.
It may ask you for a user name and password. Most times the user name is admin and the password is either admin or there is no password.
Since I don't know your exact modle, you will need to do some searching through the web portal (created by your router that you connected to with the IP) for wireless security settings.
Use something like WPA for your encryption method, or WEP if you don't have WPA. Then just give the router a pass key that you will remember.
Save the changes, and you're done.

Belkin Wireless... | Answered on May 01, 2016


do you have cordless phones running on 2.4 Ghz ?
try changing the channel number setting on the router from auto to use at least 2 channels higher than auto was using.

Belkin Wireless... | Answered on Jan 25, 2016


I had the same problem before I noticed my address bar kept adding a / after I would type the IP address so I had to make sure I hit the delete button after typing it in. Not sure if that's what you're experiencing or not. Might need to do a factory reset by pushing in on the little red button in the back for 10 seconds. I made a video showing all this with my F9K1003V1

Belkin Wireless... | Answered on Jan 02, 2016

Not finding what you are looking for?
Belkin Wireless G Plus MIMO (F5D9230-4) Router (1010835) Logo

1,187 questions posted

Ask a Question

Usually answered in minutes!

Top Belkin Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2260 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18377 Answers

steve morris
steve morris

Level 3 Expert

1675 Answers

Are you a Belkin Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Belkin Computers & Internet

  • Belkin Computers & Internet

Most Popular Question

belkin router just stopped working

  • Computers & Internet
Loading...