Top 20
Canon imageRUNNER C3220 Color Copier Questions & Answers
Mp 470 printer, how to make copies darker.
You most likely have done gradation simulation, strange that they are all light? All drums are new or in good %? have you changed out your transfer belt ITB?
12/4/2013 7:37:19 PM •
Canon...
•
142 views • 0 helpful votes
Error code 000804-004
www.digital
copiersolutions.com/cl
c-3220.html
Color Copier Canon ImageRunner C3220, Canon's true definition of multifunction has been met. should find all on here x
3/14/2013 10:23:27 AM •
Canon...
•
123 views • 0 helpful votes
How i reset E000020-0435 error
*28* the check the toner hopper if tis stock the toner or the connector check the developing unit and the toner ic then after reset all
2/19/2013 10:16:34 PM •
Canon...
•
106 views • 0 helpful votes
Error code 000000-0001
The error code has to do with the fuser unit. Try to reset the error code in service mode. If that will not clear it, you will need to replace the fuser unit...... Good Luck
1/12/2013 5:38:57 PM •
Canon...
•
217 views • 0 helpful votes
How to open service mode
This is the proceddure for all the digital copiers that Canon has. Press the additional function key, then press 2 & 8 at the same time, then the additional function key again. Screen should now indicate COPIER and any other accessories of the copier. Press the needed item, then across the top should be a series of items that you can change or look at for different needs. Be careful in this area because settings could be changed and then the copier could be dead in the water and all the stuff will have to be inputted from the start.
8/18/2012 10:02:24 AM •
Canon...
•
59 views • 0 helpful votes
Our canon C3220 is not printing from one of the computers in the office. It is putting all print jobs on hold due to authentication required
Auth Required sounds odd. The only thing i could think would cause this is if the copier itself has Department Managment enabled. This is used to limit printing by quanity and sometimes restricting color prints. IF everyone else in the office is required to enter a code to print and this one does not then you need to enable department ID via the driver settings. Right Click your print driver and go to properties and select "Device Settings" from the tabs on the top of the window. Under this menu there should be a box that says Department ID select that and try it out. Another way is to "aquire" the copiers device status a button labeled somewhat to this effect should also be in that same window.
3/13/2012 3:29:32 PM •
Canon...
•
69 views • 0 helpful votes
Can I turn the color
goto the printing preferences in the driver menu and then set the profile for the preferences for the setup u like to use .
9/8/2011 4:22:45 PM •
Canon...
•
140 views • 1 helpful votes
Ir 2270 code panne E
Hello,
tis is error code for fault in HDD. Call service for upgrade of system software and maybe you will need new hard disk.
9/6/2011 8:32:11 AM •
Canon...
•
107 views • 0 helpful votes
Error code E000003-0001on Canon ir
this is problem with the thermistor .
because the fixing temperature doesn't rise. maximum rise up to 70 degrees C.
solution is change the thermistor with a new.
this is a picture of thermistor.
7/21/2011 10:23:22 PM •
Canon...
•
370 views • 0 helpful votes
When making copies or prints,
Hello,the problem is in Magenta drum unit. Also when you replace the M drum unit replace also the ITB cleaning blade assy.Hope that helps!
9/15/2011 8:44:46 PM •
Canon...
•
76 views • 0 helpful votes
Not finding what you are looking for?