20 Most Recent Zoom X6 Adsl Modem/router Rohs (5590-00-00BF) Questions & Answers


The red light that you have there is a sign that router is having some hardware failure on it, what we can try here is to do a reset on it and see if that corrects the problem.

To reset it look for a small reset button on the router and then use a pen or paper clip then press and hold it for 30 seconds while power is ON then power off and power back on see if that corrects the issue. But if still the same you now need a new router if its still under warranty have it replace.

Zoom X6 Adsl... | Answered on Jul 04, 2011


Zoom X6 routers don't work with either Kindles or Nooks- it seems the connect on demand to save power confuses the Zoom router - typically requiring the unpractical fix of rebooting the router every two minutes.

Zoom X6 Adsl... | Answered on Jun 10, 2011


To secure your wireless network from unauthorized access,please click on this link and follow my instructions :- http://www.fixya.com/support/r3559128-wireless_router_security

Zoom X6 Adsl... | Answered on Mar 11, 2011


There will be at least 2 plugs on the modem. One will be a smaller plug, that you will plug a phone line into (if you look closely, there will be only 2 wires in that plug). The remaining plugs will be for either your wireless router (if you use one), or your computers.

Zoom X6 Adsl... | Answered on Mar 03, 2011


This WEB site gives you step by step in setting up the wireless router as a wireless repeater.

http://www.ehow.com/how_2308651_use-router-as-repeater.html

Zoom X6 Adsl... | Answered on Oct 27, 2010


I was told by ZOOM a long time ago that the X6 ADSL 2/2+ modem does not support NAT loopback.. :(

Zoom X6 Adsl... | Answered on Jun 06, 2010


You dont need the Software to do this - you can setup routers manually - by logging into them - to start lets find the correct online manual - this is the start of getting an online manual http://www.zoom.com/techsupport/adsl/adsl_5590cf.shtml Page 28 - shows how to setup the wireless security also shows details on page 13 how to login to the router - using 10.0.0.2 in an internet explorer address bar - now these are quite OLD settings - so they may still be valid or a firmware update may have changed - to check - on the PC do the following start>run {vista/7 search box}>CMD>ipconfig --- you should see a number next to default gateway if its 10.0.0.2 then thats the same as the manual - but it may start 192.168.x.x ---- so that maybe the number you need to enter into the webpage NEXT - the default username and password --- from page 14 of manual then goto the wireless section and set the WEP security you require


Zoom X6 Adsl... | Answered on Mar 25, 2010


Access your zoom router by using the laptop which still has access to the router.

Your going to have to open your Wireless Network Connection Status window located under your network settings.

If you see this window your going to left click the (details) button


Now you should see a IP DNS server address
for example: 192.168.1.xxx

Type that address onto the address bar of your web browser.

it should take you to your router setup page.

There you will need to check if the lan port is enabled







Zoom X6 Adsl... | Answered on Feb 04, 2010


Hello
No, they are specific to using cat 5 cable.
Anything else could cause a signal loss or interference.

Thanks.

Zoom X6 Adsl... | Answered on Jan 24, 2010


You may check the following:

1. Make sure to plug the power cube into a power strip or wall outlet and then plug the power cube's other end into the modem's power (PWR) jack.

2. You should only use the power cube with the Zoom X6. Other power cubes may damage your hardware.

3. Try another wall outlet.

4. Reset the modem. Use a paper clip and insert it into the RESET pinhole in the modem's back panel and press it 3 times. Then turn off the modem for a minute and turn it back on. Check if the power light will turn solid green.

5. Possible defective modem.

Hope this helps! Good luck!

Zoom X6 Adsl... | Answered on Dec 16, 2009


A router basically acts as a translator between networks to enable inter-connectivity. Your question was not descriptive enough. I think you are using a wireless router to route a wired network to a wireless one. If that is so, the router should be connected to both. For instance an ADSL or DSL Gateway router should be connected to the ISP through the wired cable and at the same time act as an access point (i.e. a getway, DHCP etc) to the local network. If this doesn't give you enough information try to clarify your question and i 'll try 2 help.

Zoom X6 Adsl... | Answered on Nov 27, 2009


Plug a network cable into the back of your PC and Router. The usually the default router page is http://192.168.1.1

Go to that page in a browser on your PC once you have conectivity. Try using 'admin/admin" to login, if that doesn't work try "Administrator/Password" keep trying a few different combos until you login to the router config page. From there you should have a section to setup the WEP/WPA key. Once you establish the security key you can set it up in your wireless lan card of your laptop.

Zoom X6 Adsl... | Answered on Nov 22, 2009


Access the Zoom Configuration Manager:
  • From a computer that is connected to the Zoom X6, open a web browser and type http://10.0.0.2 in the address line and then press Enter (or Return).
  • Enter the User Name and Password (in lowercvase letters):
    • User Name: admin
    • Pasword: zoomadsl (where "l" is a lowercase letter L)

Zoom X6 Adsl... | Answered on Oct 16, 2009


Probably means that the security is turned on, if the wireless doesn't work even after you have entered the right password then press and hold the reset button on the back of the router to restore it to defaults - factory defaults just like it was first powered on.

Zoom X6 Adsl... | Answered on Oct 09, 2009


Unplug the plug (from phoneline) on back of USB modem, plug into Zoom router. Plug one end of an ethernet cable into router and one end into your PC. Type http://10.0.0.2 into a web browser (eg. Firefox or Internet explorer) username/password is admin/zoomadsl go to basic setup and input your ISP username and password (the one given to you by your internet provider) under PPP. Click configure my connection. Save changes and then write to flash (both buttons on bottom of page)

Zoom X6 Adsl... | Answered on Jul 01, 2009


Choose your router here:
http://www.zoom.com/techsupport/adsl/adsl_x6.shtml

Zoom X6 Adsl... | Answered on Jul 01, 2009

Not finding what you are looking for?
Zoom X6 Adsl Modem/router Rohs (5590-00-00BF) Logo

59 questions posted

Ask a Question

Usually answered in minutes!

Top Zoom Computers & Internet Experts

Paul Castley
Paul Castley

Level 2 Expert

70 Answers

Prashant M
Prashant M

Level 3 Expert

2277 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a Zoom Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Zoom Computers & Internet

  • Zoom Computers & Internet

Most Popular Question

zoom x6 5590 dsl modem trouble using

  • Computers & Internet
Loading...