Canon FAX-JX200 - Answered Questions & Fixed issues

hi,
you want to set the fax, you can use the user manual guide, and follow step by step and if you can not understand, all Fixiya members can help you, if do you not have a copy you can download from Fixya; its free.

Not sure why you want to change baud rate. This should be automatically negotiated with the system you are communicating with.... What is the problem you are attempting to solve?

Incoming faxes automatically go into memory. We can't print them out. Would like incoming faxes to print out as they used to. have tried the on off button but it didn't fix the problem

Most probably is the ink cartridge problem. Please use original cartridge may solve out the problem.

Error 5100 refers to the encoder strip not being read correctly. Open the main cover so you can see the carriage (The print head, where the ink cartridges are). While it is moving you must pull out the power lead so it stops mid-travel .with no power you can move the carriage easily. Slid it to the left. You can now see the encoder strip. Its a thin translucent strip running the full width of the machine. I had black lines in it. I suspect it is dirty and wants cleaning with a cotton bud soaked in water. Run the bud along as much of it as you can. If dirty the bud will come out in dark blue. Now dry the strip with a dry bud. BE CAREFULL. do not apply any amount of pressure on it as it can break very easily. It is spring loaded. Move the carriage back to the right side. When it was on the left there may have been a wheel also of the same material up against it. Clean the round strip in the same way. Hopefully that will get it going again.

Check the baud rate of your transmissions. Slow them down to the slowest setting and send a test fax to a helpful person. Slowly increase the baud rate (communication data speed) and send the fax test. When the fax doesn't show up on the receive site, then step one baud rate speed back, and save the setting. It could also be your fax that is faulty, or even the receive sites fax, also being faulty. To test your copy-head, insert a document into your loading section of the fax and press copy. If the copy prints out fine, then you know the head is reading correctly. It is also possible that the receiver fax (the other end) has a printhead failure.

Jams in the Document TrayWhen a document jams or misfeeds in the Document Tray, <OPEN COVER> and <SEE FIG. 1> <!!CHECK!! 5100> are displayed on the LCD.NoteYou do not need to unplug the fax when clearing document jams.* When <OPEN COVER> and <SEE FIG. 1> are displayed alternatively1. Press [Stop].ImportantDo not pull out the jammed paper manually at this point.2. Hold down [Start/Copy] for a few seconds.* The document will be fed out automatically.* If the document is not fed out, gently pull the document out of the fax.* When <!!CHECK!! 5100> is displayed1. Check if any paper is jammed.If jammed, make sure to take out all the jammed paper.2. After taking out jammed paper, turn the fax off, then turn it back on with [ON/OFF].Jams in the Multi-Purpose TrayIf paper jams in the Multi-Purpose Tray, <CLEAR PAPER JAM> is displayed on the LCD.1. Gently pull any jammed paper out of the fax as shown, then press [Stop].* Pull it gently in either direction.* If you cannot pull the paper out, continue with the steps below.2. Open the Printer Cover.3. Gently remove the jammed paper inside the fax.4. Press [Stop].The fax returns to standby mode.

remove the cartridge and see if it goes away, if does then you probably have a defective cartridge are are not inserting it correctly.

Thank You,


Mikey

Here is a link to Canon for the Setup Poster to your JX500 Fax.
http://gdlp01.c-wss.com/gds/0900007828/FAX-JX500_JX300_JX200_JX201_ESI_EN.pdf

Why u need to do so?How ever this task needs service manuel u know if i say it or notIf u interested i can post u the perticular part of the service manuel!!u happymention ur email address pls

Mary:

Given that the last question I responded to for you related to a Fax JX200 - and this to a JX500 - I am not certain which model you are actually asking about. The information that follows relates to the JX500. Further, if you need information in this regard on the prior post in order to feel that the previous response was a FixYa level response, please let me know. I responded based on the information you provided...

Based on the fact that you are getting a constant 5-ring situation, it appears that the machine is in TAM (tel-ans mach) mode. The purpose of 5 falls into remote recovery of messages - toll saver results in the phone answering after 2 rings if there are messages to retrieve, and 5 if there are not. This is done to prevent long-distance charges if there are no messages.

Two ways to accomplish an 8-9 ring objective. (1) Place the machine in manual mode, which means answering every call and sending faxes to the machine. Additionally, a "fail-safe" on this mode is that it will switch to TAM/automatically answer (if there is a recorded greeting message) after 15 rings - below. (2) The incoming ring - ring count - can be set (under Fax/Tel Auto) to ring 10 to 60 seconds before the fax picks up. (3) Alternatively, the Incoming Ring ring count can be set to have the fax ring 2 to 30 times, depending on the country specific parameters.

Re TAM: When the fax is set to <MANUAL MODE> and <MAN/AUTO SWITCH> has been set to <OFF>, TAM MODE will be activated if the fax rings 15 times and the call is not answered (only when an outgoing message has been recorded). When the call is disconnected, the fax returns to <MANUAL MODE>.

If this information assists you in resolving the problem, please take a moment to rate the solution at a "FixYa" level. If you do not feel that you can rate at a "FixYa", please post back with more information regarding your specific needs, and I will gladly help you until we have reached a definitive solution. Thank you for using and rating FixYa!

I have given the solution 4 jx 300for ur machine answer is sameSearch 4 canon jx 300 chk 5100

hiLine in useYour motherboard is damaged probably due to a lightning.Machine is beyond economical repairsHave to replace a new main cardI am sorry.

THIS FAX CANON JX-200 EVERYTIME CODE 5100 WILL BE COME HOW CAN SOLVE YHE PROBLEM?

hold menu and #
press down to select clear
press Start/Copy


Trojan :)

Deleting a Document from Memory1 Press [Menu].2 Use UP or DOWN arrow to select MEMORY REFERENCE, then press Start/Copy.3 Use UP or DOWN arrow to select DELETE DOCUMENT, then press Start/Copy.4 Use UP or DOWN arrow to select the transaction number TX/RX NO. of the document you want to delete, then press Start/Copy. The LCD displays YES=(*) NO=(#). If the LCD does not change after you press UP or DOWN arrow, this means only one transaction is stored in memory. If you are unsure of the transaction number TX/RX NO., print a list of documents in memory (see page 34).5 Press [*] to delete the document.If you want to keep the document in memory, press [#].6 To continue deleting other documents in memory, repeat the procedure from step 4.To finish, press Stop.

My Serbian is not the best, but it sounds like you are having a problem on how to transfer with sound on pulsno???? dialing number. I can send you the user manual in English. Send an email to [email protected]. Put "Canon jx200 manual" as the subject.

Press [ON/OFF] to select <auto print off>The fax starts receiving documents to the memoryTo cancel press [ON/OFF] again.

I don't know this exactly machine type.Please check this extended manual:http://pdf.superwarehouse.com/specs/Canon_1735B002AA_manual.pdfMaybe you can get your answer here.

Under service mode, MENU and #, under clear, select all. After that you must reenter your settings ( fax no., line type,... )