20 Most Recent
GE Security Simon 3 Wireless Home Security System - Page 2 Questions & Answers
I have a GE home
It might not hurt to try the "Microsoft Solution" and reboot the system. First disconnect the AC power then disconnect the battery. Wait 1 minute then reconnect the battery and reconnect the AC power.See ifyou can arm and disarm the system. Then reconnect the siren and try again to arm and disarm the panel. If the keypads beep it can usually give you an error code that will help you pinpoint the problem.
I have an old Westinghouse Security Systems that
Check all ur windows and doors sensoring connections,might need to be changes.Weather is too hot or too cold,will trigger the alarm.When u arming tries by passed and any error codes for doors or windows connections codes.This should stop the fault alarm by the expanding and contracting sensors by the weathers.
How do you remove the control panel on Simon 3?
There is a couple steps in removing this panel. First, unplug the unit and then locate the tab on the top of the unit, it has to be pushed down. When the tab is pushed down the first faceplate should drop down, exposing the keypad with the menu options. Second, you need to get a small flat head screwdriver and put it under the clip at the top of the panel. You can locate it by finding where your pushed the original tab down; it's right below that. Once you have your screwdriver under the small clip, push the clip up and pull the 2 faceplate towards you. Finally, after the second plate is down, unscrew/unplug the wires from the panel, unscrew the mounting panel and your done! Beware, depending on how your alarm is hooked this can cause a short to your household telephone lines causing them not to work!
Don't have the access code
Do you mean the access code for turning off an alarm or arming the system before leaving? If so, NO. You would have to know the original code to even enter programming to change the access code. Contact your realtor and have them get you in contact with the previous owner. Find out the code from them. If they properly removed their code before moving from the house use the default code, 1234. Good Luck.
How do I change the battery in the GE Simon XT
If your system is monitored call the central station first and tell them you are working on it. Then push down on release tab in top center to fold down the front face. Nest step is to use a small flat blade screw driver to push in and release the tab again in the top center and the unit will fold down towards you, hold on to it and you will see the battery compartment. Follow the red and black wires to the battery. Some units have a plastic lid over the battery that requires you to remove to small phillips screws to remove battery.
How do u reset the passcode on the ge simon 3 system.
There are many kind of passwords: master, dealer, user 1,2,3,4
and panic code.
You have to enter to the programing mode the default is 4321
if this does not work you have to get the code from the company who sold it to you, so you can entrer the access code level which is the first section that appear once you have enter the right installer code after you reach the system programing section. Ouhsin the OK let you in using the arrow to scroll down let you go to other sectio of the program the OK is the enter button
Changed battery on simon 3 monitor but now phone line is down
If, as you say, you just changed the battery and had no phones right afterward it's likely that you accidentally loosened the phone jack inside the back of the panel(accessible when unit is opened to change the battery). Remove and then re-insert the phone-jack clip, usually on a wide flat cable, and carefully tuck/fold the wires in the hollow area so no pressure is on the phone jack & wire;recheck phones.
Low cpu battery how do i fix it on alarm system
Open the system, unplug the transformer, disconnect one lead of your battery, reconnect the battery first, then the Ac if it says low battery still, then you need a new battery take the one you have go to battery plus get a new one, and reconnect it, it may still say low battery, wait for an hour for the battery to charge, disconnect the AC and battery again, reconnect the battery first then the transformer. It should clear the low battery.That battery is a 6 VDC 1,.9 Ah.
Not finding what you are looking for?