Top 20 HP LaserJet P2015 Printer Questions & Answers

some times this printer problem on toner chip.some times problem processing print defective on LSU

The problem is most likely the formatter board. This is the board that the printer cable plugs into. You can buy a replacement or try to fix this yourself buy baking the board in the oven. The board is easy to remove, just pry the side outer plastic off, pull the wire connectors and remove the screws holding it on. The issue is that the solder joints are not good. If you have some solder skills then you can attempt to heat up all the joints with your tool to make the joints reform or you can place the board on a cookie sheet in the oven for 15 min on 350 degrees and let the oven do the work.

That suggests that the problem was not with the feeder or shaft, but with a sensor. Can you check the sensors, or cal a service agent?

Check the fuser unit

Hi, May be cable loose or heavy dust available in printer that`s why your printer not proper response it. Or may be printer main board damage position so i suggest you contact it printer technician or checking it, which area damage. http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01764440&tmp_task=solveCategory&cc=us&dlc=en&lang=en&lc=en&product=3811075 Thanks, HP Printer Support

Hi check the toner, if you have one for testing may be old and will take away the doubt

Try this press and hold the go button while powering on the machine

Release the "Go" button when the triangular "Attention" light on the control panel illuminates. The factory default settings for the printer will load once you have released the "Go" button on the control panel.

HP LaserJet P2015 Series Printer - Replace the pickup roller (tray 1)

1. Unplug the power cord from the printer, and allow the printer to cool.
2. Press the print-cartridge-door button to open the print-cartridge door.
3. Remove the print cartridge. After removing the print cartridge, only handle it on the ends.
4. Grasping the pickup-roller cover with thumb and forefinger, squeeze the left side of the pickup-roller cover to release the left retaining tab, and then slide the cover to the left and up. Failure to slide the cover to the left when removing it can cause the right retaining tab to break.
5. Press the two black retaining tabs outward until the pickup roller is released from its seat.
6. Remove the old pickup roller from the printer.
7. Line up the black retaining tabs in the printer with the grooves in the new pickup roller, and then press the pickup roller into the pickup-roller seat until the retaining tabs click. Do not touch the pickup-roller pad.
8. Grasping the pickup-roller cover with thumb and forefinger, insert the pickup-roller cover's right retaining tab into the retaining slot.
9. Squeeze the left side of the pickup-roller cover and insert the left retaining tab in the retaining slot.
10. Close the print-cartridge door.
11. Plug the printer in.

SIR I Suggest You To Please Watch below link Url Video: www.youtube.com/watch?v=et0tLRbK4yU To Fix Your HP Printer Problem, Or In Case You Still Have Problem Then Follow Us On: HP Printer Support

yes

go to the Hewlett Packard website for the drivers

First see the printer is new or old model.if it is new then go tn setting and set autoprint

download the driver

Does the attention light blinking?

You may download the HP driver from http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareIndex.jsp?lang=en&cc=us&prodNameId=1845552&prodTypeId=18972&prodSeriesId=1845551&swLang=8&taskId=135&swEnvOID=228

Check paper, and check toner.

Removed all covers and check shutter. up under the top cover is the laser scanner shutter.

You can download the HP printer drivers from their support WEB site. Please click on this link and select your model printer to download :- http://welcome.hp.com/country/us/en/support.html

May be a problem with your driver...try it again ...what error you are getting???If you need any kind of technical assistance you can contact support cell at http://www.vtechsquad.com/