Bissell 2070 QuickSteamer Vacuum - Page 3 - Answered Questions & Fixed issues


Hello, this is Ava with Think Crucial.

You may view the online manual for your Bissell model on how you can replace dust bag by clicking the link below.

Bissell ZING 22Q3 SERIES User Manual Dust Bag Replacement

You can purchase a wide variety of high quality Bissell replacement parts for your Bissell vacuum direct from Think Crucial with free shipping and an exclusive 10% coupon for Fixya.com readers, use code: FIXYA10

https://www.thinkcrucial.com/collections/vendors?q=Bissell

I hope this was helpful.

Ava B.
Think Crucial Customer Care
http://www.thinkcrucial.com/

Bissell Vacuums | Answered on Aug 06, 2017 | 612 views


Hello, this is Ava with Think Crucial.

You can purchase a wide variety of high quality Bissell replacement parts for your Bissell vacuum direct from Think Crucial with free shipping and an exclusive 10% coupon for Fixya.com readers, use code: FIXYA10

https://www.thinkcrucial.com/collections/vendors?q=Bissell

Ava B.
Think Crucial Customer Care
http://www.thinkcrucial.com/

Bissell Vacuums | Answered on Jul 30, 2017 | 36 views


There is still a blockage in the tube that feeds the bag.

Bissell Vacuums | Answered on Jul 29, 2017 | 34 views


You would see if you warped the tank, the issue is most likely related to melting some of the thin pump parts or tubing in the unit. Bissell does not sell those parts to the public. Find a repair center or send it in unless you want to buy a new one. PS in the future don't put high temp water in the tank, put it on the spot you are trying to clean and then vacuum it up.

Bissell Vacuums | Answered on Jul 22, 2017 | 45 views


Go to Bissell web page an down load manual. I would send link but you did not list model number.

Bissell Vacuums | Answered on Jul 19, 2017 | 47 views


Could be the switch or the motor, or the circuit board. Take it to your local vac shop for diagnosis.

Bissell Vacuums | Answered on Jul 03, 2017 | 39 views


It's either too full or if you emptied it maybe you didn't get it back together right and the seals are not in correctly. Double check the assembly

Bissell Vacuums | Answered on Jul 03, 2017 | 60 views


Bissell 2X machines are famous for this. The brushes not turning is probably just a broken belt but the not spraying is a bad solenoid. I've never seen a 2X that didn't fail after about 6- 8 uses

Bissell Vacuums | Answered on Jul 03, 2017 | 79 views


I would suggest taking it to your local vacuum cleaner store and have them look at it. Most bagless cleaners need to be serviced annually to maintain performance.

Bissell Vacuums | Answered on Jul 03, 2017 | 33 views


The 2X is designed with 5 solenoids. I am not allowed to tell you that it's a flaw in the design, but I will say that is the only machine on the market that our store refuses to work on. Buy a Hoover F5914-900 machine and end your pain.

Bissell Vacuums | Answered on Jun 12, 2017 | 34 views


Try Googling (Bissell)(model)(manual) without parens.

Bissell Vacuums | Answered on May 20, 2017 | 27 views


Some (not all) of them have a wire or switch that the filter must press back between the filter and the back of the vacuum. It prevents the vacuum from running unless the filter is installed correctly (they never tell customers about this)

Bissell Vacuums | Answered on May 06, 2017 | 80 views


Hi. This is not as easy as you'd think. If I were you, I would go to YouTube and type: bissell 9400-3 hose replacement in the search box. They will most likely have a video of someone working on a similar machine.
Good luck!

Bissell Vacuums | Answered on Apr 30, 2017 | 37 views


The check valve on the bottom of the bladder wasn't going deep enough into the recepticle on the base of the unit; the valve wasn't opening, and the pump was sucking from a dead end. (It WOULD pull soap from the small tank, but not the main bladder reservoir.) I cut a 3/4" piece of a disposable ball-point pen cap, to ride over the rod in the center of the recepticle. Long enough to push the valve open, but short enough that the tank assembly sat down on the base. If the rod is too long, it will push the whole tank up, and break the vacuum seal at the forward edge. Evidently this thing was designed to a tight tolerance, and just a little aging/distortion of the plastic reservoir base was just enough to keep the valve from being pushed open!

Bissell Vacuums | Answered on Apr 29, 2017 | 39 views


this mite help you

Bissell Vacuums | Answered on Apr 15, 2017 | 175 views


There is a flapper door that blocks suction when the pickup tank is full so water won't be drawn into the motor. Sometimes that flapper will shut off too soon and stop the suction. The Bissel web page has all the parts you'll need to fix it.

Bissell Vacuums | Answered on Apr 15, 2017 | 38 views

Not finding what you are looking for?
Bissell 2070 QuickSteamer Vacuum Logo

Popular Tags

4 questions posted

Ask a Question

Usually answered in minutes!

Top Bissell Vacuums Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18408 Answers

Brad Brown

Level 3 Expert

16181 Answers

Jim Thurston

Level 3 Expert

670 Answers

Are you a Bissell Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...