20 Most Recent Danby DMW139 Microwave Oven Questions & Answers


There are sixty seconds in a minute, so 1 min 60 sec is the same as 2 min. If you want 40 seconds less than 2 minutes then set it for 1 min 20 sec or for 80 sec.

Danby DMW139... | Answered on Oct 03, 2013


If you had posted your brand and full model number, I probably could have given you a part number and specific supplier.

You can find links to helpful exploded view diagrams and part ordering help for most brands here.

I recommend that you bookmark that link to your favorites.

We're happy to help you with free advice and we'd appreciate your thoughtful rating of our answer.

Danby DMW139... | Answered on Oct 06, 2011


Hi,
Here is a tip that will help you to figure out what is wrong with yourMicrowave Oven....

Microwave Oven Basic Troubleshooting Tips

heatman101

Danby DMW139... | Answered on Jun 26, 2011


Replacement of the lamp should be carried out by a qualified appliance repair service.

YOUR SAFETY IS PARAMOUNT!

Attempt this only if you are competent.

But here is a basic method if you are mechanically minded and have electrical safety knowledge.

The lamp is sat in a housing and its position is adjacent to the vent holes that it shines through.
If you feel confident, disconnect it from the mains power, remove anything in the cavity.
Remove the microwave cover. Purchasing a new replacement lamp will be useful as it will give you an idea of what it looks like. Locate the dead lamp remove the lamp and fit the new one. Replace the covers. Plug it back in and try the lamp by opening the door.
Hope this helps.

Danby DMW139... | Answered on Feb 20, 2011


It indicates the magnetron is getting to hot "that heats the food" when that happens the thermal fuse opens to protect the magnetron from over heating and shuts it down and waits until it is cooler before it resets. The other problem could be the fan not working or not properly that blows on the magnetron, it helps keeps the temperature regulated so it can run hard. If it turns out the fan is fine, then the magnetron is slowly breaking down until it becomes unusable, which means it will need to be replaced "pricey" or buy new "probably cheaper"

Danby DMW139... | Answered on Jan 20, 2011


You might check to see if the fan is turning and the vents behind the fan are clear. It's possible the magnetron is over heating causing the oven to shut down.

Danby DMW139... | Answered on Jun 08, 2010


If it blows as soon as you hit the "Start"pad to cook, it has a shorted high voltage capacitor.

Danby DMW139... | Answered on May 28, 2010


HI,
this will require the skilled hands of a qualified tech. the damaged part here is the Magnetron assembly. this is a very sensitive part that creates radiation and the heating process as well. you will need to replace this device asap if possible...

thank u
rate me

Danby DMW139... | Answered on Jul 13, 2009


Im sorry to say, but the housing will have to come off to unlatch the door from the inside.Not difficult ,Unplug the unit and remove all of the screws around the top of the housing cover if any,also
rear and both sides will have to come out.When they have all been removed, lift the rear of the top housing cover and pull back.You will be able to see where the two door latches are locked in place.With a screwdriver,you can push up on the bottom latch and the door will open. All this can be done without spilling the milk inside.Just slide the microwave around slowly to get to the screws.The broken part inside should be able to be replaced.Contact repair parts center.

Danby DMW139... | Answered on Jan 11, 2009


You can contact Danby Customer Service US / Canada.

We're happy to help you with free advice and we'd appreciate your thoughtful rating of our answer.

Danby DMW139... | Answered on Dec 13, 2008


This is usually caused by either a bad door switch, a loose door switch mount, or a problem on the control panel.

Even though a door switch clicks, it may still be bad inside.

This can be caused by slamming the door or by habitually opening the door while it's cooking without hitting the Stop pad first.

If you or a friend decide to look into it, we have critical information on safety, disassembly and door switches at our site, and our link is at our listing here on FixYa: http://tinyurl.com/yzjozk

We're happy to help and we appreciate your thoughtful rating of our answer.

Danby DMW139... | Answered on Dec 04, 2007


The first thing to try is a "hard reset": Unplug it from the power line for a few minutes, plug it back in, then try again.

If that doesn't fix it, can you describe the icon? Does the manual show the icon?

Please write back with more details if you need further help.

This may be a bad door switch, a loose door switch mount, or a problem on the control panel.

If you or a friend decide to look into it deeper, we have critical information on safety, disassembly and door switches at our site, linked here on Fixya: http://tinyurl.com/yzjozk

We appreciate your thoughtful rating of our answer.

Danby DMW139... | Answered on Dec 02, 2007


What does the service center have to say about this?

Or did you do it yourself?

Danby DMW139... | Answered on Dec 02, 2007


check mains supply and check control pannel,

Danby DMW139... | Answered on Nov 23, 2007

Not finding what you are looking for?
Danby DMW139 Microwave Oven Logo

26 questions posted

Ask a Question

Usually answered in minutes!

Top Danby Microwave Ovens Experts

William Miller
William Miller

Level 3 Expert

9174 Answers

vince

Level 3 Expert

1234 Answers

gbob59

Level 3 Expert

3042 Answers

Are you a Danby Microwave Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Danby Microwave Ovens

  • Danby Microwave Ovens

Most Popular Question

after setting time cook 1 min 60 sec

  • Microwave Ovens
Loading...