20 Most Recent
Kenwood 2005 KDC-MP5028 CD/MP3 ReceiverFree Standard Shipping Questions & Answers
BLAUPUNKT radio mute and volume haywire
yea the got a short somewhere. Horn fuse might or might not work something with the radio. I would say start with the horn. The horn is a controlled short sometimes shorts it self out. Open your steering wheel and work from there. For your radio look at all the fuses that you know work the radio and go from there. What kinda car is it year things like that would help because if it older wires, fuses, fusible links things like that go bad over the years. Especially if you run a lot of power through the wires that was made for that kinda power like upgraded speakers, headunit (radio) amps things like that. Older cars and trucks are make with cheap radio wires. hope this helps
I have a mp5028 and it tells me 2 enter the code.
you will need a remote for this
Common Kenwood Security Codes
Many Kenwood radios are configured with the same security codes:
KCAR - This seems to be a "backdoor" to some Kenwood models.
3051 - This is the security code which is printed in the manual of many Kenwood models.
1234 - This is a security code commonly chosen by Kenwood owners.
Entering Your Kenwood Security Code
If the car battery fails or is disconnected, the Kenwood will ask for the security code.
The
procedure to enter your security code differs on various models of
Kenwood car stereos. Here are three of the more common procedures:
Type 1
During
the code request mode, while holding the DISP key depressed, press and
hold the Volume UP or DOWN key for 3 seconds until the "..." display
disappears.
Enter the security code using your Kenwood remote.
Type 2
Press the "Auto" button and "Track up" on the face of radio at the same time until the four dash lines disappear.
Enter the security code using your Kenwood remote.
Type 3: Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset keys until the display shows the letter 'C'.
Enter the security code using your Kenwood remote.
Entering Letters on your Kenwood Remote
To
enter a letter using your Kenwood remote, press a button once for the
first letter, twice for the second letter, and three times for the
third letter -- then press the Track Up or Next Track key to send the
letter.
To send the letter 'A', press the 2 key once and then
press the Track Up key. To send the letter 'B', press the 2 key twice
and then press the Track up key.
Finally, when you are done entering all of the letters, press and hold the Track Up button for 3 seconds.
The key sequence to enter the security code KCAR is:
5
5
Track Up
2
2
2
Track Up
2
Track Up
7
7
Track Up
Your Kenwood should then enter tuner mode.
A Security Code Bug in some Kenwoods
There
is a reported bug in the security code handling of some Kenwood
stereos. In models with thie bug, the security code is stored
incorrectly. The workaround is to enter the wrong security code.
In
models with this bug, you have to decrement the third character of the
security code by one. If your security code was 1111, you would enter
your security code as 1101. If your security code was 9999, you would
enter 9989.
Unlock code for kenwood model kdc mp5028
Hey there joe,
Click here, it
will bring to a Tip page authored by one of our best
technicians (Robotek). He outlines the procedure for clearing the code
on most Kenwood models.
If this gets you going, don't forget to give Robotek a rating Remember: Good things come to those who Rate!!
Mike
Kenwood Tuner Frequency Steps Problem
MichaelBlackDo you know where I can find the remote key combination to do the same with KDC-MP538U? (To transform it to the European system)
Thanks in advance!
How to set europe freq on KENWOOD KDC-BT838U car radio
Last night i got the answer from KENWOOD Support
Press and hold in the SRC button until the unit turns off. While power is OFF,
press and hold FNC and AUTO/TI buttons, and momentarily press the SRC button to
power the unit back on. Continue to hold the other buttons until the unit comes
back on completely.
I did it and it works
Enjoy
Kenwood KDC-MP5028
with the unit in standby, press the menu key, use the joystick control to choose aux, and set the aux option to "on"...then press menu again to save...when you next switch on the unit, using the SRC button you can cycle through the available options...cd - tuner - aux..etc etc
My car stereo
on your radio there should be 2 sets of outputs high and low you probably have set to low just switch to high and run your speaker wires accordingly to amp
Is it Dead?
hi it sounds like the cd mech is wurring so power should be ok.
try RESETTING the unit with the reset button, you will need a pen tor a pin to do this in most cases. if still no joy, then double check that you are getthing two pwer feeds to the radio
1 should always be there this is the perminant power feed. and the other4 should only be there when the ignition is on.
let me know how you get on.
Mark
Blue ICE
www.blueice-electronics.co.uk
Forgot my code.
try this
KENWOOD SECURITY CODE CLEAR procedure
Your radio will require one of the following procedures.
Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds (so that “…” disappears).
Then using your remote enter your code.
Type 2
Press the "Auto" button and "Track up" on face of radio at the same time. The four dash lines ( . . . . ) should "disappear".
Then using your remote enter your code.
Type 3
Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset key (preset keys are the buttons on face of radio for storing you "favorite" radio stations). "C" should display.
Then using your remote, enter your code.
Enter your number from the remote control unit. Your code number is 5227 (KCAR)
* Press numeric key “5” ( 2 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 3 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 1 time ) and press the Track UP/Next Track key
* Press numeric key “7” ( 2 times ) and press the Track UP/Next Track key
The security is canceled and the set enters the TUNER mode!
Kdc-w4534
" protect " is flasing on my w534 cd player and my cd player will not work any more . any ideas
Not finding what you are looking for?