20 Most Recent Ricoh Aficio SP C320DN Color Laser Printer - Page 9 Questions & Answers

1. Check the power supply source. 2. Replace the +24V fuse on the PSU. 3. Replace the PSU

sc 303 is ac charge output error ( Y drum) Possible Causes • Disconnected or broken high voltage cable •Yellow PCU could be defective or not installed • Defective high voltage power supply

SC350: ID Sensor Error Possible Causes · ID sensor defective · ID sensor connector defective · Poor ID sensor connector connection Dirty ID sensor · Defect on the drum at the ID sensor pattern writing area

sc 672 Controller-to-operation panel communication error at startup Possible Causes ? Controller stalled ? Controller board installed incorrectly ? Controller board defective ? Operation panel connector loose or defective ? The controller is not completely shutdown when you turn the main switch off. Check the setting of SP5875-001. If the setting is set to "1 (OFF)", change it to "0 (ON)".

sc 532 is IH coil fan error. fan motor could be defective .overload on the IH coil fan motor .disconnected harness or defective IOB board

without knowing the sc code it will impossible to help because there are more than one fan in mp c2500 each one has different code and different locattion

check and clean the toner rack connector

Possible fixes: Translated using Google translate: https://www.gebruikershandleiding.com/Ricoh-Aficio-SG-3110DN/handleiding-5-536387.html -------------------------------------------------------------------------------- https://translate.google.com/translate?hl=en&sl=nl&u=https://www.gebruikershandleiding.com/Ricoh-Aficio-SG-3110DN/handleiding-5-536387.html&prev=search -------------------------------------------------------------------------------- 28113 - Ink supply timeout error (Tank 3 error) • ink supply pump error • air sensor error • The tank feeler is malfunctioning. • ink level senor error • The ink supply pump is faulty. • The carriage is faulty. • The ink level sensor is faulty. • The CTL board is faulty. • Turn the main power switch off and then back on. • Replace the ink supply unit. • Replace the carriage unit. • Replace the air purge detection switch. • Replace the CTL board.

1) Perform the printer reset and the issue will be resolved. Unplug the printer's power cord from the socket and disconnect any USB cable connected with the printer. 2) Wait for few minutes until the carriage stops and the printer becomes silent. Re-connect the power cord and cables to the printer. 3) Power on the printer and perform the test print. The printer should work fine and the red light should not blink. 4) Make sure the paper loaded in the input tray is same as like the one you mentioned in the paper type. For more support visit our website @ https://goo.gl/4bc47n.

Chapter contents SG 2100N SG K3100DN SG 3110DN SG 3110DNw SG 7100DN User... Contents SG 2100N SG K3100DN SG 3110DN SG 3110DNw SG 7100DN User Guide Troubleshooting Ricoh Printers YouTube

you need change ink collector unit.

SC491 Richo 2050

How can I clear error sc 20000 0n richo ipsio sg 7100 printer WHEN i PUT PRINTER ON RED ALERT LIGHT ON ERROR sc 20000 WHAT CAN i DO

Likely dirty drum

need need new tires in tray 1

SC-990 - Communication problem between BICU and input output board or software performance error. I would suggest contacting Ricoh customer service.

From things I have read about this error code, it could be happening because of using compatible sublimation inks which is causing this problem. Check out the following link: https://www.dyesubforum.co.uk/vbforum/archive/index.php/t-13457.html

Try replacing the power cable that goes from the wall to the machine.The type of power cable used in the MP C3000 & C4500 has a hard plastic insert where it plugs into the machine that can get damaged by impact and short out. Also try checking the wall socket to verify that it is completely plugged in. Worse case scenario it could be an I/O board. If you have a contract with Ricoh, I would suggest placing a service call for them to come out and look at the machine.

What you are looking for is the Ring Count Delay. Unfortunately it looks as though this is not an option for this unit. Here is the manual for the MP C4501. http://support.ricoh.com/bb_v1oi/html/oi/re/model/mpc41/mpc41en.htm If you need a service manual. https://www.service-manual.net/?download=53457-ricoh-aficio-mpc4501-aficio-mpc5501-series-service-manual