20 Most Recent Maytag Atlantis MAV6000 Top Load Washer - Page 3 Questions & Answers


You may want to check the seal at the bottom of the agitator, there is a o-ring that keeps the water in the drum from leaking through the agitator as it spins. This is a cheap seal and will wear over a period of time from exposure to bleach and detergent. You need to take the agitator apart and remove it from the drum and you should see this seal at the base of the agitator were it meets the drum.

Replace the seal and reassemble, take the metal casing off the washer and fill the drum with a little water, wait, and see if the water is leaking under the drum. If no leak, try to reassemble and run the washer. If is still leaks then check http://www.applianceaid.com/genew.html

Yours Truly,
Mr.Fix-it-guy

Maytag Atlantis... | Answered on Oct 19, 2014


change the water inlet hose screens as they are plugged,also put the hoses on a hot water line and run hor water thru them and see what comes out of them in the sink,then replace the washer inlet hose screen

Maytag Atlantis... | Answered on Sep 24, 2014


The water inlet valve has something caught between the diaphram & body or the diaphram is split. If it is the type with screws in it you can pull it to pieces, remove the foreign matter or replace the diaphram if damaged (if you can buy one). Alternately replace the valve.

Maytag Atlantis... | Answered on Sep 22, 2014


If you do it yourself it will be about 40 dollars and a few hours of your time. Have someone else do it for you and it will be about 200 dollars

Maytag Atlantis... | Answered on Aug 23, 2014


Hi,

If this unit is older then 5 years, check the belt and see if its just stretched, this happens in the unit, part number if you need it 22003483, this is cheap to replace and will most likely correct the spinning and draining issue you have. Good Luck

No tools require to replace this belt, its under the unit, bring unit toward you and tip back to the wall. The belt crosses 3 pulley's

I’m happy to help further over the phone at https://www.6ya.com/expert/gere_bf68e6055dd61249

Maytag Atlantis... | Answered on Aug 08, 2014


Draining problem;
About the noise. If stumbles on the wash cycle and no noise occurs, is transmission problem. If the noise is present all the time the coupler that is located between the transmission and motor needs to be replace!

Maytag Atlantis... | Answered on Jul 29, 2014


Good question! I wondered this too... But I just did this last week and I was successful... Lets see if you can be too.
First.. How old are your hoses? Are they getting stiff? Maybe time to invest in new ones... Especially the hot one... For heat makes these hoses age quicker.. And pick up a couple screen type hose washers for each end, if they are not already on your new hoses... Or if you are not changing hoses this time.
OK... Now you see how to turn off the water?
Turn it off and bleed the pressure off by attempting to fill the machine....
Now a pair of slip joint pliers helps to loosen the connector. . start at the supply valve end... See the screen... Right there in the end of the hose? Is it dirty, clogged? Or maybe even rusted and failed? Maybe you are glad you invested in the new hose? If so, just install the new hose. If not... Do you have access to compressed air? Can you take the hose to a friend and blow it out?. If not try removing the screen type hose washer... If you have to destroy it getting it out... You have new washers.. Install them... Likely there is one at each end.
Now... Before you hook it all back up... Can you blow air thru the hose easily? Then hook up the hoses to the water supply ends at the wall... Put the hoses in an empty bucket... Turn on the water valve... Do you get a real strong flow of water? If so.. You are ready to connect to the washing machine end also. Now does the machine fill up g fast again? What did you find? Let us know... We are here to help. MB

Maytag Atlantis... | Answered on Jul 26, 2014


  1. You sound pretty capable of digging deeper into this solution... So let's proceed together... Removing the front of most top loaded is easy... Two screws and push it up, until it releases at the top. Now... What do you see?... Is the motor spinning? Did the safety ' out of balance switches get knocked out of position? Tell us what you see, lets take it to the next level off trouble shooting... MB

Maytag Atlantis... | Answered on Jul 26, 2014


Sounds like a bad fill sensor

Maytag Atlantis... | Answered on Jul 24, 2014


No, If water is coming back, the sewer is cloged up or is a big posibility that the washers transmission is not spenning at all. it may sound like is agitating during the wash and spinning during the rinse. To check it, put soap inside the drum if it doesn't get disolved after the cycle is done. The transmission needs to be replace. Is costly you may want to shop for a new one.

Maytag Atlantis... | Answered on Jul 22, 2014


this is my experience repairing the maytag washer Atlantis mav series 9750 aww, I had to replace the spin bearing since it was making a jet engine noise when it was spinning out the water. its not an easy job for my 1st time taking this machine apart, you literally take it all apart to get to this bearing, but now I can show how to do it with pictures making it easier for you to do it. even if you have to replace something other than the spin bearing, this how to tutorial will show you how to get to most of the parts in this machine
tutorial located here tutorial located here https://sites.google.com/site/maytagwasherrepair/maytag-washer-repair

Maytag Atlantis... | Answered on Jul 05, 2014


I HAD TO REPLACE THE SPIN BEARING ON MY MAYTAG ATLANTIS WASHER MAV9750,
it was making a loud noise during sin cycle, like a bad bearing would
make, jet engine kind of noise, i did replace the bearing and made a web
site with pictures on how to do it, since it almost takes all the parts
out, it will show you how to get to most of the parts in the machine, and
i also included links for downloading the repair manual, and parts at
appliance parts pros web site
http://maytagwasherrepair.googlepages.com/index.html

Maytag Atlantis... | Answered on May 20, 2014

Not finding what you are looking for?
Maytag Atlantis MAV6000 Top Load Washer Logo

1,252 questions posted

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

jimorris77

Level 3 Expert

411 Answers

Sheldon Dedek

Level 3 Expert

909 Answers

Bill Long

Level 3 Expert

606 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Maytag Washing Machines

  • Maytag Washing Machines

Most Popular Question

remove maytag inner tub

  • Washing Machines
Loading...