20 Most Recent Linksys Wireless-G WRT54GL Router - Page 4 Questions & Answers

First and foremost, did you start with the Holy Grail of steps when dealing with routers? 30-30-30 YES! It does make a difference and it matters. Hopefully you haven't bricked it (probably not). If it is powered on, press and HOLD the reset button until the VERY END, DO NOT LET UP. Holding the reset button for 30 seconds, then unplug the power and wait 30 seconds, plug power back in and wait 30 seconds. . . NOW you can let up on the reset button. Now you can try and reflash the firmware, DO make sure you are using the correct version of DD-WRT for your EXACT model AND Version. I have only done a few, but the 30/30/30 is crucial I am telling you!

Check the available memory on your PC. It may be limited and far too small for the operation you are running. Same thing happened to me

not really unless you were to run an ethernet cable from your existing network to a location outside of the current wi fi range. A repeater would be better https://www.tomsguide.com/us/best-wifi-extenders,review-2225.html It hears the wi fi signal so you put within the signal range near where the signal still can be heard near the extent of the current wi fi range. It will hear the signal and then re-transmit it to extend the signal range . You might be able to use a gain antenna of 5dbi 2dbi is lost in the cable usually so it is 3dbi which is twice the level http://computers.mwave.com.au/electronics/High-Gain-Antenna another method would be a omni directional antenna facing the coverage range . But it is beaming in one direction . which means more signal strength in one direction https://www.mwave.com.au/product/draytek-ant1207-highgain-omnidirectional-indoor-antenna-black-ac04622

It depends on the power capability of the EA7400! Usually, those ports are rated at 500ma, or 0.5 amps each. If you plug in a non-powered hub into one of the ports, it will draw power from the EA7400 to operate. If the power draw needed exceeds the capability of the port, it won't work properly. A powered hub relies on an external power source. In that case, only data collisions (oversaturating the ports) need to be considered.

hi yvo2000. Sorry, you cant do that. That router (well, the SPA2102) needs a cable from your neighbor's router in order to provide internet to the POTS jacks. Please don't forget to rate my answer if it helped you. Thank you :D

Any type of technical issue can solve by taking a few minutes with our expert technicians who always ready for customer help. If the customer wants to get solution about all that problem, contact our Linksys Router Service Number +1-(833)-284-2444 for the USA which is totally toll-free number. There are available very expert technicians who will be helped you and provides your technical problem solving, and they also are connected online service between customer system, it service available for 24*7 hr. or customer can visit for more solution with our website. https://servicenumber.org/

Contact MAC support.

try use a more stable routers like DLink routers.

What is the model of your Linksys rotuer? How many computer and devices are connected? Who is your internet service provider? Are all the devices offline? Make sure that your router is setup properly with the modem. Below is the link which may help you with Linksys router. Linksys router setup Easy Guide

Hi, What are you typing in chrome to reach your browser?

Hi, Please provide more information. Where are you getting the error? How are you attempting to connect to the router?

When you come across a profile that spreads hot news, be wary. Fake profiles have been long used to give an air of credibility to those who spread fake news on social media. <a href="http://www.buyinstalike.co.uk"> </a> <a href="http://www.buyinstalike.co.uk">BUY INSTAGRAM FOLLOWRS UK</a>

I'm trying to get into CISCO LINKSYS E1200 router but I can not find a way to get in, it's to configure ports for a DVR. https://translate.google.com/

The simplest way to reset the range extender is to press and hold the reset button on the side of the unit for 5-10 seconds. The LED will start blinking. The button is recessed and is close to the WPS button. You can use a ballpoint pen or the end of an unfolded paperclip. Now you will have to connect the RE6700 to your router as if it was brand new. See https://www.linksys.com/us/support-article?articleNum=138012 for more information. I hope this helps. Cindy Wells