20 Most Recent Aiwa TV-S2011 20" Questions & Answers


Check and replace damaged component/s at its horizontal scan output section circuit. Check the LOT (Line Output Transformer) too for damage. Replace the horizontal scan output transistor. Check the input voltage to LOT. If absent check the feeder resistor; if any. If you wish to get some details; check the site linked here. Viewing it in "Mosaic" will make surf easy. Surf the site with patience. Pull up older posts.
http://electronicshelponline.blogspot.com/

Aiwa TV-S2011... | Answered on Apr 04, 2014


Check and replace damaged component/s at its audio output section circuit. Contact any service technician. If you wish to get some details; check the site linked here. Viewing it in "Mosaic" will make surf easy.
http://electronicshelponline.blogspot.com/

Aiwa TV-S2011... | Answered on Feb 21, 2014


Check it video output section circuit for any loose solder terminals. This board can be located at the neck of the picture tube, directly plugged on to it.

Aiwa TV-S2011... | Answered on Jul 08, 2013


Its main system control memory IC is damaged. Replace it with same number. This IC is a very small one, having 8 solder terminals, and can be located very near to the main system control IC. Usually start with a number 24C**. Check and replace it. If you wish to get more details, surf this link. http://electronicshelponline.blogspot.com/ There are more than two thousand and four hundred posts. All are related to television and other domestic electronic equipment service help.

Aiwa TV-S2011... | Answered on May 17, 2013


Check it LOT {Line Output Transformer] and horizontal output stage circuits for any fault.

Aiwa TV-S2011... | Answered on Apr 29, 2013


power cable damaget, get new one

Aiwa TV-S2011... | Answered on Apr 20, 2013


Hello
Check your remote control hanset for proper functioning. Get into this link to know more about the faults and repair to remote contorls.
http://www.fixya.com/support/r10192276-cleaning_remote_control_handsets

If remote control functions proeerly, the front panesl switches to be suspected. If any one mong the microswitches inside got strucked, all functions will be distrubed. it will be best to follow any more after replacing these microswitches. These switches can be located just behind the control panel of the tv, soldered diretly to a printed circuit board. You have to replace all of the at the same time. Just undolder one amoung them as as sample, when you go to buy for a new one.
If this also does not help you, repalce its memory IC. This IC can be located very near to the main system control IC, will have 8 solder terminals. A very small IC and wont cost more. Eventhough it is very small, function of it when the set works is great. Replace it. When you buy this IC, make a keen look on it number. It is very important when replacing this IC. All these components stated above, can be bought from most of the electronic spare part selling shops st your town. OK.

Aiwa TV-S2011... | Answered on Feb 07, 2012


see on your remote control there will be three empty space in button columns if you open your remote control circuit board then you find there three hidden keys by pressing one of them the aging error will desapear

Aiwa TV-S2011... | Answered on Dec 03, 2011


I have Aiwa TV MODEL No. TV-A149
The problem that I am suddenly facing is that I can't change channels or volume or use any other function. I can't even turn it off with remote control.

Its stuck randomly on a particular channel that I was watching at that point of time.

Along with that channel it now shows a message in flashing red color that reads :-
AGING
6EDEH

Now when I press ''Display'' button on remote control volume goes off and this code is shown :-
S123 K234 Y
100 000 0


The numbers in the second line can be navigated by ''CH+'' button and changed between 0 and 1 by ''Vol+'' button.

I really don't know anything about this. So, please help me out of this problem.

Aiwa TV-S2011... | Answered on Dec 03, 2011


Picture tube is magnetized. Manual degausing is required. already you have done this.

Since you say it is reappearing, you have to check the following.

1. Relocate the TV or relocate if you have placed any tower speakers
or home theater speakers close-by.

2. Check whether auto degauss functioning OK. In the MENU
check whether you switched off auto degauss option. If it is OFF
enable it to ON.

3. Finally re orient the direction of your TV and watch the rainbow
effect. Switch OFF TV, wait for 20 mts, and again switch ON.
Repeat the process. It should disappear.

Magnetic toys or any other devises using magnet will cause this problem.


Aiwa TV-S2011... | Answered on Feb 03, 2011


Hello
Aiwa TV is not lited on Jumbo Universal Remote codes. Anyway try out with these codes. Sometimes may help you.

Three digit codes for Aiwa TV with universal remote are:
195/ 196

Four digit codes for Aiwa TV with universal remote are:
0195 0196 0227 0269

Direct Code Entry
  1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
  2. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.
  3. Enter the 4 digit code from the code tables. Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes.
  4. With your device on, press CHANNEL UP. If the device responds, no further programming is required. Note: If some buttons do not operate your device, try one of the other codes for your brand.
Code Search If after trying "Direct Code Entry" your device does not respond, or if your brand is not listed, try doing a search of the code library for your code by following these steps.
  1. Manually turn on the device (TV, VCR, etc.) to be controlled.
  2. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
  3. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks once, then stays on.
  4. Press the CHANNEL UP button repeatedly (up to 300 times) until the device to be controlled changes channel. The red indicator blinks, then stays lit.
  5. Press and release MUTE to install the code. The indicator light goes off.
Most users will want to store VCR codes under the VCR button, Cable codes under CBL, etc. If you want to store a VCR code under CBL, etc., first follow the procedure for Direct Code Entry and press CBL in step 2 of Direct Code Entry, then enter ANY VCR code in step 3 of Direct Code Entry. Then follow the steps above for Code Search.

NOTE: Switch OFF and switch ON your TV with its FRONT PANEL POWER ON-OFF SWITCH each time before trying an other code.
OK

Aiwa TV-S2011... | Answered on Jan 27, 2011


Hello
If power supply is not coming inside your tv, the fuse inside it may blown out. There may be some resons for that. Sometimes it may be to a overvoltage problem. Otherwise due to an overload problem. Sometimes inner components may got shorted, especially mains retifier diodes may be leaked. If this is the condition, you must retify that problem first before replacing the the fuse. A multimeter is needed to check this; and to check for all faults.
Never replace the fuse assuming that the fuse only is blown out. Please understand that there may be a reason for that. If you do so, so many other components in your TV also will get damaged.
As your TV is in "dead" condition; we say this condition thus, we can't predict the exact fault point or assume the suspected fault point in your TV. It is best for you to get a technician at service. Please don't spoil your TV by doing self repair; unless you are fully aware of it schematic diagram. Aiwa TV uses some special components of their own, which cannot be bought from local market. Get it serviced by any experienced service technicians, or send to the authorised service center nearby for repair. Ok.

Aiwa TV-S2011... | Answered on Oct 19, 2010


no audio / please send me the frequency for ahmedabad city

Aiwa TV-S2011... | Answered on Aug 17, 2010


maybe your aiwa tv has a loose connection in the board needs to be resolder the jungle ic

Aiwa TV-S2011... | Answered on Jun 19, 2010


It is really a memory problem try to access its service mode open the cover of its remote control so you can find an extra carbon switch inside which is not accessible if the remote control's cover is on.Another way is you can use an eeprom copier copy a known good aiwa ctv with the same model or parameters

Aiwa TV-S2011... | Answered on Feb 13, 2010


i wish you could just shared the problem of your tv here,i would have assisted

Aiwa TV-S2011... | Answered on Feb 24, 2009

Not finding what you are looking for?
Aiwa TV-S2011 20" Logo

38 questions posted

Ask a Question

Usually answered in minutes!

Top Aiwa Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76054 Answers

 Grubhead
Grubhead

Level 3 Expert

5686 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you an Aiwa Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Aiwa Televison & Video

  • Aiwa Televison & Video

Most Popular Question

error codes

  • Televison & Video
Loading...