20 Most Recent AEG 18 in. Favorit 64800 Free-standing Dishwasher Questions & Answers

This control procedure is in operation only during the cold wash and heating phases.

• Once the pressure switch has closed in the "full" position, it must remain "full" until the subsequent drain phase; if the pressure switch signals "empty", the fill solenoid is activated for a period equivalent to the period of aperture of the pressure switch.

• The maximum aperture time for the pressure switch (T) during the entire phase is 60 seconds; if this period is exceeded, an alarm condition is generated.

Alarm: AL5 Possible causes:

1. Dishes upside down
2. Central filter clogged
3. Siphon effect created in drain hose
4. Leakage in sump - pressure switch tube.

Dado

AL03 - HEATING TIME-OUT The maximum heating time for the water is 45 minutes; if the correct temperature is not reached within this time, an alarm condition is generated. Possible causes:

• Heating element broken
• Safety thermostat open
• Wiring interrupted / disconnected
• NTC sensor faulty / incorrectly positioned / poor thermal contact

Dado

When the motor is switched on, it must reach a speed of 1300 rpm within 10 seconds; if this doesn't occur, A7 alarm condition is generated. Possible causes: Motor winding short-circuited, motor winding interrupted, motor jammed, electrical connections broken or false contacts, tachometric sensor broken or short-circuited. Dado

Hi, I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works like new... However I have also foundthat if the heating element goes bad then that also can mess things up bad...So I would buy new spray arms, and also check out the heating element to makesure it is working... Here is a tip that will help you with the onlinebuying...
Dishwasher SprayArms not Spinning

How to Buy ApplianceParts Online

A bad heating element causes many problems in dishwashers...

Dishwasher Problems The HeatingElement not Working

DishwasherMaintenance DishwasherResidue and Film on Dishes

heatman101

Asker's Testimonial "explanation very clear. will give it a go and see howsimple it was. thanks Ronnie " - ronnieshomes

; '' '; ';;'

al4 is tripping of anti flood float switch in base of machine. look for a leak mopping out the base resets the switch

This seems like the anti flood system (polystireen float / micro switch) at the base of the washer is triggered,\. This puts the washer in pump out mode and stops inlet of water via the inlet solinoid. Dry the water on the base and then check for any water leaks. (pipe leak

try calling this no. 0844 800 3456 they should give you a price.

Question edited for clarity. It is likely to be a control board issue. They are expensive, so call for diagnostics and service. The reason the dishes aren't clean is because it is stuck on wash, so there is no draining and rinses. This machine has some history! https://www.google.com/search?q=aeg+f34300vi0+dishwasher+keeps+running ..

If your AEG FAVORIT 35085 Vi dishwasher beeps five times and stops halfway through a wash cycle, there could be a few potential causes for this issue. One possibility is that there is a problem with the water supply, such as a clogged or partially blocked inlet valve. Another potential issue could be related to the drainage system, such as a clogged filter or a malfunctioning drain pump. It's also worth checking if the dishwasher's spray arms are spinning freely and not obstructed by any debris. If the problem persists, it is recommended to consult the dishwasher's manual or contact AEG's customer support for further assistance. They can provide specific troubleshooting steps and guidance based on your dishwasher's model and any error codes that may be displayed.

If the anti-flood device has activated on your AEG dishwasher, it means that water has leaked into the base of the dishwasher and triggered the safety device. The anti-flood device is designed to prevent water damage to your home and shut off the water supply to the dishwasher. To resolve this issue, you will need to locate the source of the leak and fix it. Here are the steps you can take:

1. Turn off the dishwasher and unplug it from the power outlet.
2. Disconnect the dishwasher from the water supply and move it away from the wall.
3. Check the inlet hose, outlet hose, and drainage hose for any cracks, damage, or loose connections. Tighten any loose connections and replace any damaged hoses.
4. Check the dishwasher door and gasket for any damage or debris that may prevent it from closing properly.
5. Check the dishwasher's interior for any leaks, such as a cracked spray arm or a damaged pump.
6. Once you have fixed the leak, you can reset the anti-flood device by tilting the dishwasher to one side to allow the water to drain out of the base. Then, level the dishwasher and plug it back in.

If you are unable to identify or fix the leak, it is recommended to call a professional technician for assistance.

no info generic answer inlet valve failure --short in valve circuit

Did you check the emergency shut off switch? Almost all under the counter dishwashers have a wall switch to interrupt the power. The problem is it can be shut of on accident.

Look at the screen on the drain.if its clear then check your drain for leaks
As it could be building pressure on the system..by not draining proper.

If you are reading this, then you probably own an AEG dishwasher with a ceiling arm. This part is important for the dishwasher to function properly and needs to be cleaned regularly. However, if it becomes loose or falls off, it can be a real headache to try and reattach it. In this article, we will walk you through the process of how to fix a ceiling arm back onto your dishwasher.

I would check for any bends in anything... a crimp of a wire or bend of a hose can mean the washer will not complete setup and will just refuse like a stubborn mule. If you find no bends or crimps in wires... the brain may be dead. It will be one solid motherboard and should be fairly easy to replace.