Maytag Neptune MAH9700 Front Load Washer - Page 8 - Answered Questions & Fixed issues

What is the model number?

Heather, just replaced mine last week, it's a quick replace about 5 mins top. when removing the old one start at the bottom right corner and and pull towards you and just do the opposite when installing the new one. good luck.

YOU FAIL TO MENTION THE BRAND NAME AND MODEL NUMBER, WITH THE INFORMATION YOU GAVE, MY BEST ANSWER IS TO TAKE IT APART AND CHANGE THE BELT AND REASSEMBLE IN REVERSE ORDER WITHOUT ANY PARTS LEFT OVER. MY ANSWER PROBABLY HELPED YOU AS MUCH AS YOUR QUESTION HELPED ME.

ND NO DRAIN

The most likely cause of a DC error code on a Neptune is the clutch assembly.

Sounds like a bad water inlet valve, have it checked with a multimeter and some appliance parts store can check it for u before u purchase another one? call and ask them/

If there is water in the unit and the temps drop below freezing, then yes, it will freeze. If you are storing it, ensure that all water is out of the lines and drum because when water freezes, it expands and can break hoses and pipes.

door open=do bad door switch

only way to stop it is empty your pockets

Hi, Here a website for you with a video that will assist you in this repair. Good Luck Maytag Neptune Bearing Replacement How to Replace Neptune Tub Bearings I’m happy to help further over the phone at https://www.6ya.com/expert/gere_bf68e6055dd61249

Unplug it from the wall, open the door, disconnect the lock wire from the latch. cover the wire end with tape.

Water valve pump is bad. It look something like that.

Download repair manual from link below. http://www.applianceblog.com/mainforums/threads/13498-Maytag-Neptune-Repair-Manual Maytag Neptune Door Locked but No Spin R11 is not burnt

www.searspartsdirect.com/partsdirect/brands/Maytag-Parts

The problem of residual water in front load washers is an on going problem. Some companies had put in a small drain hose in their units to alleviate the problem. Your washer is actually built by Whirlpool. There is no available auxiliary drain for these models. These are the suggested solutions to alleviate for your particular machine. 1. Leave the door open after wash completed. This will help to evaporate the residual water. If in an area where the door cannot be left fully open then place a towel over the top of the door to keep it from closing and that will help by keeping the door open a small amount. 2. To alleviate odor, pour one cup of bleach in the drum... DO NOT PUT ANY CLOTHES IN THE MACHINE! Put the washer through a wash cycle... some models had a clean cycle if your has this then use this cycle. Once this has completed remember to do a white load following this procedure to assure that if there is any bleach residual then it wont cause problems with colors. 3. Dry the door seal after each use... this will eliminate mold from developing on the door seal. If you see mold then use a bathroom cleanser for mold removal to clean the seal... DO NOT USE A SOLUTION OF VINEGAR... THIS COULD DRY OUT THE SEAL CAUSING IT TO CRACK THUS REQUIRING REPLACEMENT. FYI: The Maytag Company went bankrupt sometime ago, the name Maytag wash purchased by Whirlpool and appears on products to secure the business of faithful Maytag users...

try un pluging washer for 15min and plug back in to see if it resets. if not u may need new latch but first make sure u don't have a loose wire to lock

In some cases it is a simple adjustment of the Levelers. Use a flat level device to check the levels from front to back and side to side. Make certain the Washer and Dryer have a space between them and they do not bang into one another.

WHY DO YOU WANT TO DO THIS IT IS NOT SAFE FOR YOU OR YOUR FAMILY IF THEY GET HURT HOW WILL YOU FEEL ARE YOU INSURED FOR THIS

you may have a broken heater

If it\'s not draining properly and shows this F02 Code there may be a simple solution. Take the bottom front panel off (it has 3 screws.) There will be an off white circular plastic thing there. Resembles the top to a cannister. Twist it off. There will be a good bit of water if tub hasn\'t drained properly. Put a cookie sheet under it to catch most of the water or get a shop vac and suck it out slowly. Once you completely unscrew the top off hopefully your problem will be right there. Cleaning out the drain hose ... the hose may nee to come off the machine and pulled it out of the drain - it could be seriously blocked with all sorts of build-up. Like if you wash one of those rubber backed rugs --- don\'t do it again - the particles will come off and pack into the drain line and pump. It is an easy fix