20 Most Recent Maytag Neptune MAH9700 Front Load Washer - Page 9 Questions & Answers


Hi Joe

Is that pex pipe on the right your water supply to the washer?

Your sewer gas smell I believe can be eliminated by putting a P trap in the drain PVC line.

(EDIT)
Where the drain hose from the washer hooks into the PVC pipe is NOT airtight which would allow the sewer gas back into the laundry room!

(EDIT EDIT)
If there is a P-trap in your outflow pipe, the only place left for grey water to collect (and stink) would be between the washer and where the waste hose goes into the drain. We've had to use a little bit of bleach on occasion when we haven't used the washer for a bit.
Hope this helps
-Steve

Maytag Neptune... | Answered on May 02, 2015


check pump for blockage

Maytag Neptune... | Answered on Apr 28, 2015


door inter lock can b opend by removeing lid fiddley job

Maytag Neptune... | Answered on Apr 27, 2015


LE means level error. The water fill timer timed out before there was enough water in the machine to clean the clothes. Try this:
  1. Turn the hot and cold water supply taps, located at the end of the fill hoses, as far as they will go toward the "Open" position.
  2. Move the washing machine away from the wall, and examine the hot and cold water pipes for kinks, twists or other obstructions.
  3. Unscrew the fill hoses at the washing machine, and inspect the small plastic screens inside for signs of an obstruction.
  4. Check the water pressure in your home; a reading lower than 30 psi might cause the fill times to extend beyond the time the washing machine is programmed to wait. Slow flowing faucets and shower heads are a sign of low water pressure.
  5. Call for service.

Maytag Neptune... | Answered on Apr 20, 2015


Please check fill valve. It is possible something stacked and it letting water in

Maytag Neptune... | Answered on Apr 17, 2015


I assume you mean it sounds like a jet plane when it spins, if so, I suspect a bad tub bearing. Depending on age of the machine, probably too expensive to repair.

Maytag Neptune... | Answered on Apr 02, 2015


bearings? or sometimes litle things can get stuck in between tub and housing and cause funny noises

Maytag Neptune... | Answered on Mar 29, 2015


Door or Lid Latch Assembly If the washer won't spin or agitate the lid switch assembly might be defective. This is a very common problem. The lid switch assembly can fail either mechanically or electrically. Test any electrical switches with an Ohm meter for continuity. The switches should have continuity according to their design. Motor Coupling If the washer won't spin or agitate the motor coupling might have failed. The motor coupling connects the motor to the washer transmission. It is designed to fail if the washer is overloaded in order to protect both the motor and
Drive Belt If the washer won't spin or agitate, check the drive belt. If the belt is broken or if it isn't tight on the pulleys the washer won't spin or agitate properly.
Transmission or clutch assembly not engaging due to going out or slipping.



Maytag Neptune... | Answered on Mar 29, 2015


No agitation or spin? try these:
Motor Coupling If the washer won't spin or agitate the motor coupling might have failed. The motor coupling connects the motor to the washer transmission. It is designed to fail if the washer is overloaded in order to protect both the motor and
Drive Belt If the washer won't spin or agitate, check the drive belt. If the belt is broken or if it isn't tight on the pulleys the washer won't spin or agitate properly.

Drive Motor If the washer won't spin or agitate the drive motor might be defective. This is not common. Check all of the other related parts to this symptom before replacing the motor. If the motor is visibly burned out or physically damaged, replace it.

Stator Assembly If the washer won't spin or agitate the stator assembly might be burned out. The stator is essentially one half of a motor, it interacts with the tub by creating a strong electro-magnet. If the stator burns out the washer won't spin or agitate. Check the stator for continuity. This part is often misdiagnosed.

Transmission or clutch assembly not engaging due to going out or slipping.

Door or Lid Latch Assembly If the washer won't spin or agitate the lid switch assembly might be defective.

Door Lock Motor and Switch Assembly If the washer won't spin or agitate the door lock assembly should be checked. The door lock can fail either mechanically or electrically. Test any switches on the door lock with an Ohm meter. The switches should have continuity according to their design.

Motor Control Board he motor control board provides power to the motor as well as direction and force. If the motor control board is defective the washer may not work at all or function properly.

Maytag Neptune... | Answered on Mar 29, 2015


check ur hoses doubt its ur tub having a hole?

Maytag Neptune... | Answered on Mar 29, 2015


call maytag repairman

Maytag Neptune... | Answered on Mar 16, 2015


yes, that sound is normal. it is not actually water, but a balancing liquid that is sealed behind tub/drum. all is well.

Maytag Neptune... | Answered on Mar 11, 2015


Hello Joanna;

My name is Peter. I am a retired field service appliance technician. I do still work at my trade on the side.

The "NF", means no fill. Check the following:
1.) Go to No Fill Test.
Enter / Exit Service Mode To enter Service Mode press the Help and Back keys for three seconds or until the control beeps. The motor speed will be displayed when started (motor not running display will be 0). Diagnostic codes will be shown and the System Check or Service utility can be started. The present state of the machine will not be changed. (i.e., the current cycle in progress will not be interrupted and only the display will change).
2.) Check to make sure water supply is turned on fully. Normal water level is 1 to 7 inches inside the spinner. 3.) Check electrical circuit and connections at the water valve, and pressure switch. 4.) Check for kinks in inlet hoses. 5.) Check for clogged inlet screens. 6.) Visually check hot and cold separately for fill. 7.) Check for low water pressure. May be dependent on pressure entering home. Variations may occur due to usage in the home at the time machine is used. 8.) Check for frozen pipes and hoses.

Chances are you have a bad fill valve and sensor. I can repair this for you. I need to check the component with my Ohm meter. My charge would be $40.00 for the part and $50.00 for the diagnostic and labor.
I will not charge your my former Sears Home Services Charge of $79.00 to show up at your home + Part price x 2 + $150.00 labor.

Glen Burnie, MD
443-306-1362


Maytag Neptune... | Answered on Mar 05, 2015


replace coin unit

Maytag Neptune... | Answered on Mar 03, 2015


Vinegar on anything. If it is all plastic use CLR or a generic equivalent the same you would remove the calcium buildup from around a faucet.
25425705-1mk4yrcyljvj1vw5me2rbfsm-4-0.jpg

Maytag Neptune... | Answered on Feb 14, 2015


Check behind the front panel at the base the machine

Maytag Neptune... | Answered on Jan 16, 2015


in the water lines at back .

Maytag Neptune... | Answered on Jan 15, 2015

Not finding what you are looking for?
Maytag Neptune MAH9700 Front Load Washer Logo

167 questions posted

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

jimorris77

Level 3 Expert

411 Answers

Sheldon Dedek

Level 3 Expert

909 Answers

Bill Long

Level 3 Expert

603 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Neptune Maytag

  • Neptune Maytag

Most Popular Question

maytag neptune error code nd

  • Washing Machines
Loading...