Technical Support, Instructions & Repair Service
Home | My Products | Sign In

Online User Manual and Guide for Denon DHT500SD System

Denon DHT500SD System > User Guide
Showing Page 8 out of 37 Previous     4 5 6 7 [8] 9 10 11 12     Next
Search keywords inside this manual:

Let Our Experts
Solve
Your Problems
Ask!
Loading problems.


Showing Page 8 out of 37 Previous     4 5 6 7 [8] 9 10 11 12     Next

Sponsored Links

© 2005-2008, FixYa, Inc. or its affiliates
8 ENGLISH A A B C C D E (1 or 2 speakers) • The ADV-500SD's red speaker terminals are the “+” (positive) terminals and the black terminals are the “–” (negative) terminals. • The  “+”  side  of  the  speaker  cable  is  marked  to  make  it  distinguishable  from  the  “–”  side  of  the  cable. Connect this marked side to the red “+” terminal and the unmarked side to the black terminal. • Prepare the speaker cords for connection by stripping off approximately 10 mm or less (no more as this could cause a short-circuit) of the outer insulation. Twist the wires tightly together so that they are not straggly. SPEAKERS FRONT (L/R) CENTER REAR (SURROUND)(L/R) SURR.BACK SUBWOOFER      - BLACK BLACK BLACK BLACK    + RED RED RED RED CAUTION: To avoid damaging the speakers with a sudden high-level signal, be sure to switch the power off before connecting the speakers. (2) Connection to Speakers (SYS-500SD) Speaker Connections CAUTION: The  metal  portions  of  the  two  separate  wires should not touch or an electrical short can occur. Shorted wires can create a fire hazard or induce a failure in your equipment. Press the lever, insert the stripped and twisted end (approx. 3/8") of the cord, then release the lever : Make sure it is fastened securely by pulling the cord lightly. How to connect Connection the speaker terminals 1. Push the lever. 2. Insert the cord. 3. Return the lever. Positioning of the Speakers The positioning of speakers differs according to the size   and   acoustics   of   the   listening   room.   While actually  listening  to  a  program  source,  try  various speaker    positions    to    determine    which    layout provides the best surround effect. Place  the  speakers  connected  to  “L”  to  your  left, and “R” to your right. A Front speakers (SC-A500SD) Place  the  front  speakers  in  front  of  the  listening position, to the left and right of a TV. Front speakers are required for all surround modes. B Center speaker (SC-C500SD) Place a center speaker between the front speakers, on or below the TV. This speaker stabilize the sound image. C Surround speakers (SC-A500SD) Install   these   speakers   above   the   level   of   the listener's ears, to the left and right. Do not install the surround speakers too far behind the listening position. It might be effective to direct the rear speakers towards a wall or ceiling to further disperse the sound. D Passive Subwoofer (DSW-500SD) Reproduces powerful and deep bass sounds. Subwoofers  are  most  effective  when  placed  on  or near the floor and in a corner of the room. Refer to the instructions that came with your subwoofer for placement suggestions. E Surround back speakers (SURR. BACK SP.) If  you  add  the  Surround  back  speaker(s),  you  can enjoy  6.1  ch  surround  sound  or  7.1  ch  surround sound. (ex: DOLBY DIGITAL EX, DOLBY PRO LOGIC IIx, DTS ES, DTS NEO 6, etc.) Place the speaker behind of the listening position. G SURR. BACK PRE OUT jack Use SURR. BACK PRE OUT jack to connect additional POWER AMPLIFIER and two speaker systems. You can enjoy 7.1ch surround system. ADV-500SD POWER AMPLIFIER (for SURR. BACK ch) •   Connect the power amplifier for center and SURR. BACK speaker system. IN SURR. BACK (L) Speaker SURR. BACK (R) Speaker IN H AC Power Cord When all the connections have been finished, plug the AC power cord into an AC wall socket. G TO AC outlet H