HP C1315A 9100c Digital Sender Token Ring - Page 41 - Answered Questions & Fixed issues


The printer is warming up and is not ready to accept data. Wait until the printer signals ready. If necessary, press On Line.

HP Office... | Answered on Mar 25, 2016 | 29 views


  1. Open Devices and Printers by clicking the Start button , and then, on the Start menu, clicking Devices and Printers.
  2. Click your printer's icon, and then click See what's printing on the command bar.
  3. Right-click the document you want to reprint, and then click Restart.

HP Office... | Answered on Mar 25, 2016 | 233 views


Some tests require the Administrator password via the web interface, otherwise you'll only be able to access general diagnostics under the Troubleshooting tab. Users guide accessible from HP at http://goo.gl/O0kYei

HP Office... | Answered on Mar 18, 2016 | 118 views


go to control pannel
add device
search for your device or connect you device

HP Office... | Answered on Mar 17, 2016 | 38 views


that might be your printing settings and laptop file formate

HP Office... | Answered on Mar 17, 2016 | 126 views


If you want to do a cold reset, then you must turn machine off. Turn machine on and when the memory count starts, hold down the ok key. When all three leds on control panel stay on solid, use the 9 button to advance through options. When you find cold reset press the 6 button, unit will restart with most settings back to factory. network card may not reset.

HP Office... | Answered on Mar 16, 2016 | 44 views


http://support.hp.com/us-en/product/HP-Deskjet-Ink-Advantage-All-in-One-Printer-series---K2/3811342/model/3811361/drivers

HP Office... | Answered on Mar 16, 2016 | 35 views


http://support.hp.com/gb-en/document/c00297388

HP Office... | Answered on Mar 15, 2016 | 28 views


Okay let's try this please.

Below is a recommended suggestion to resolve this problem:
  1. Upgrade the FW
  2. Remove the ITB
  3. Remove the fuser and on the left side (front of printer side) you can see the sensor flag holder (image #1 and #2 below)
  4. If the sensor flag/lever is stuck in the up position then reach in and carefully release the part with your fingers. The images below show the sensor flag/lever stuck in the up position. Actuate the flag/lever a few times to make sure it is loosened up.
  5. Re-install the ITB
  6. Re-install the fuser
  7. Reboot to see if the error clears
If the issue returns in a short period of time, then the flag/lever is likely dragging and returning slowly or getting stuck again. If this occurs, then it is recommended to:
  1. Remove the top cover
  2. Inspect the POSITION DETECT ASSY RM1-5604 to ensure the photo interupter is seated correctly
  3. Check the sensor flag for proper movement
  4. Replace the POSITION DETECT ASSY RM1-5604
NOTE: The ITB is typically not the cause of this issue.
I hope this helps.

Please do not forget to rate if helps thank you and have a wonderful day...

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/josem_e9ac89730196f220

HP Office... | Answered on Mar 19, 2016 | 66 views


Sometimes you have to open up the machine as much as possible, without removing hardware, to expose the inside. Shine a bright light inside to locate the jammed paper and use a suitable tool such as tweezers to pick it out piece by piece.

HP Office... | Answered on Mar 14, 2016 | 26 views


Look up Phillips on the internet. Put in or look up the model number. They are likely to have an instruction book that you can download.

HP Office... | Answered on Mar 13, 2016 | 30 views


I cannot make out from your question which device.
Could you be more specific with the model? See below.
There was LJ5500 and DJ5500 and DesignJet 5500 etc



26126176-1ghxgn5fx50lkeiwquwdurxw-2-0.png

HP Office... | Answered on Mar 11, 2016 | 34 views


I did not determine the cause of the error. But did find that powering the printer down, then up, resulted in the document being printed without further travail.

HP Office... | Answered on Mar 08, 2016 | 978 views


Should do as long as you can hear the ink moving when you shake them next to your ear

HP Office... | Answered on Mar 06, 2016 | 33 views


Have you tried the machines own programme to clean the ink jet heads ?

HP Office... | Answered on Mar 06, 2016 | 380 views


I would say clean out the paper route as its obvious something could be causing the problem

HP Office... | Answered on Mar 06, 2016 | 180 views


Use the internal programme to clean the ink jets

HP Office... | Answered on Mar 05, 2016 | 103 views


uninstall software reinstall

HP Office... | Answered on Mar 05, 2016 | 30 views


That cartridge is no good and needs to be replaced.

HP Office... | Answered on Mar 05, 2016 | 29 views

Not finding what you are looking for?
HP C1315A 9100c Digital Sender Token Ring Logo

0 questions posted

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts

Clive
Clive

Level 3 Expert

4345 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18429 Answers

Cindy Wells

Level 3 Expert

5761 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...