20 Most Recent
Hotpoint Aquarius WF000 Front Load Washer - Page 3 Questions & Answers
Filter
most hotpoint have a hidden filter
take back bottom panel off. you will see a large diameter hose coming from tub to pump. undo hose at tub end. filter is inside this hose. take it out and clean it
9/27/2013 1:01:29 PM •
Hotpoint...
•
Answered
on Sep 27, 2013
Hotpoint aquarius wf320
Hi charlie99 Peace,
ngafm At your service!
With an error code the only way to find and to repair this is,
First unplug the washer and wait a few minutes then restart it like rebooting your computer when its acting strange!
If it corrects the problem GREAT.
If not only a trained laundry tech can make the electronic diagnoses.
How old is the appliance?
If the appliance is 10 years old or more you it may not be advisable to put good money into bad!
New appliances are so much more efficient today that they can save you a lot of money in energy!!!!
Water,Electric and detergent! And put money back in your pocket!
The new appliance will pay for itself in only a few years!
Bless You ngafm
PLEASE GIVE ME A GOOD RATING HERE AT FIXYA.COM BEFORE YOU SIGN OFF.
Thank You
8/13/2013 10:29:05 AM •
Hotpoint...
•
Answered
on Aug 13, 2013
Hotpoint Aquarius WF100 Fabric Cond not rinsing thru & PreWash lite flashing
this sounds like cold water supply not getting to the machine, test the supply from the house is working, is the machine buzzing slightly when it should be filling, if so the fault is the house supply to the washer, if the supply to the washer is fine, check the cold water solenoid for open circuit, thats about all it could be, if it worked fine before, if i have helped rate me please
8/2/2013 9:43:35 AM •
Hotpoint...
•
Answered
on Aug 02, 2013
Fabric conditioner stays in the dispenser tray
the holes above the fabric softener tray that shower into it may be blocked. use an upturned washing up brush to scrub them with a little fairy liquid and see if that works, it does for me. also could be a water pressure issue.
7/30/2013 1:34:38 PM •
Hotpoint...
•
Answered
on Jul 30, 2013
Replace drum bearings on hotpoint aquarius wf000g
You really don't want to know how but here it is. The bearing is located in the rear shell and is not removable the rear shell has to be replaced which means removing the tub assembly from the machine and completely disassembling. With 30 years of appliance repair the last one I did took about 3 hours.
5/27/2013 9:38:44 PM •
Hotpoint...
•
Answered
on May 27, 2013
Reduce crease and mini load lights flashing on
I have encountered a similar problem. The following lights were flashing on and off:
- On/Off.
- Reduced creases.
- Mini Load.
I also found that previously one of the 'lifters' inside the drum had
broken off and someone had tried to put it back in place and continued
to use the washing machine. After a short period of time the above
mentioned flashing lights began.
I first suspected the pump, but this was fine. I then disconnected the
hose which connects the hole from the drum to the pump and I found a
child's sock blocking the hose. I removed the obstruction, put it back
together and the machine worked perfectly. I also replaced the lifter
(apparently these break quite often) and the machine has been working
perfectly ever since that day.
I hope this helps. Good luck.
2/8/2013 7:29:25 PM •
Hotpoint...
•
Answered
on Feb 08, 2013
Led key light flashes on my mwa64 hotpoint washer
Possible that the INLET and OUTLET - DRAIN filters are clogged or there is limited action. Remove and clean inlet and drain filters.Also check on the connectors from the panel, reset all connections.
1/17/2013 10:44:48 AM •
Hotpoint...
•
Answered
on Jan 17, 2013
Hotpoint WT960 Flashing F-05
This is a drain problem. Most likely something caught in the pump which is accessed by removing the small panel at the rear/bottom of the machine. The pump slots in place and can be removed by lifting and shifting to the left. Unscrew the pump off or remove the pipes will reveal all.
1/4/2013 7:41:38 PM •
Hotpoint...
•
Answered
on Jan 04, 2013
HOTPOINT AQUARIUS WF 250 ON/OFF LIGHTS FLASHING
The lights are set off by the balance sensors.And if your balance sensors are stopping it from spinning than you first have to make sure the washer is level.You could have bad Shocks and a bad electronic control board,.
12/10/2012 7:28:14 PM •
Hotpoint...
•
Answered
on Dec 10, 2012
Hotpoint aquarius drive belt wont go on
hook the belt around the motor spindle first then get the belt as far round the pully as you can once at that stage hold the belt firmly as you can on the pully and turn the pully round making sure that the belt does not slip off keep turning the puully round till the belt is fully on once on spin the drum around by hand to make sure that it is on the pully square with motor spindle. job done. if this helped please leave feed back.
10/9/2012 11:02:41 PM •
Hotpoint...
•
Answered
on Oct 09, 2012
Not finding what you are looking for?