20 Most Recent Hotpoint Aquarius WD640 Front Load Washer/Dryer - Page 3 Questions & Answers


sometimes a bad thermal shut off will cause the blinking lights and then agin maybe a bad control board

Hotpoint... | Answered on Jan 02, 2015


F12s low water pressure, normally either te taps stuck or the fill hose is kinked/blocked

Hotpoint... | Answered on Dec 28, 2014


check that your skin pipe is not blocked....happend to me with different make washer.....kept tripping when it came to spin.....skin pipes were clogged with hard oil/grease soon as a clean the pipe it was fine

Hotpoint... | Answered on Dec 23, 2014


Error code F13 indicaters dryer fan or dryer thermistor faulty.
These are to be be found in the top of the washer on top of the heater manifold.
To access them remove top cover.
Please rate my solution.
Thankyou.

Hotpoint... | Answered on Dec 23, 2014


Disconnect from mains. Remove rear panel and water will probably come out. This water is being flung by the fan onto the heater hence tripping the electric.
cause of water being here is a blockage in the condenser stopping flow into water chamber or possibly but unlikely, failure of the pump

Hotpoint... | Answered on Nov 25, 2014


Check the carbon brushes of the motor. And then press the button start for about 5 sec. until all leds lights up.

Hotpoint... | Answered on Nov 15, 2014


The dryer fan or dryer thermistor (thermostat) is faulty.
If the fan is working, then replace the thermistor, or check for broken wire.
Please rate my solution.
Thanks.

Hotpoint... | Answered on Nov 15, 2014


Fit new timer switch to avoid heating if you bypass it it will go flat out and burn out the element.

Hotpoint... | Answered on Nov 15, 2014


There is a small thermostat button ontop of the Heater mechanism which has tripped . It has either a red dot or blue dot ontop. Use a pin or opened up paper clip and push through the red wax. It will go click and it is reset. .
It sometimes trips out with a F code which normally trips the machine off because it thinks the Heater unit is on fire.
There is a small disk which costs about £15 to buy which you can change. You will need HEX screwdriver set to change and open up the Heater matrisx to clean the fluff off the element.

318c857c-2bc5-40ec-ab21-f6fe52de17a6.jpg


error-code-f13-brswrwcy453xu5qdcnkktuei-3-2_0.jpg


error-code-f13-brswrwcy453xu5qdcnkktuei-3-3_0.jpg

Hotpoint... | Answered on Nov 15, 2014


Is it still under warranty? I've read that these machines are better left at the retailer...

Hotpoint... | Answered on Nov 15, 2014


f05 say pump blocked or pressure switch fault. whereas f11 say pump cannot be activated... so either an open circuit pump or fauty pcb..

Hotpoint... | Answered on Sep 21, 2014


It is a tricky job but the heater thermostat switch has tripped as it senses something burning. Probably a little bit of fluff on the heater element inside the heater unit.. There are 2 switches on top of this heater unit. One where the 2 blue wires goon the top left of the 3rd picture and the other which has a tall black wire connector on shown in the middle of the 3rd picture. Remove that connector and undo the holding screw . You can then reset the switch.
The switch is a small circular switch hidden beneather the connector on the photos. This thermostat switch has a yellow. red dot ontop of it. If you use a small pin or needle and press into that dot you will hear it tick back into place. you have reset the switch now.
You will probably need to clean the inside of the heater element unit to get rid of the fluff particles or it will keep switching off.
To take this apart you will need a set of Star screwdrivers. Its a bit tricky but you will be able to undo the star screws and take them all out. I will add some photos to show you the unit apart.
You can see the build up of fluff on the photos i have added from my hotpoint WD860 heater unit.

This is a tricky job and takes about an hour due to the screw being awkward to take off and put on again but mine hasnt faulted for 2 years since sorting it out.
You can buy a new Thermostat switch which is about 10 pounds sterling from Hotpoint or other
be91b32f-a289-4249-a4d0-499e2094e901.jpg 95adeccb-a83d-4edc-99a4-f08bf4669b6c.jpg 8af03867-1caf-4748-adb6-379e0dca1507.jpg fd076e29-d1d9-414a-8a0d-c18654b08aab.jpg ab17c040-2aaf-46c0-b85b-42e5d4817547.jpg cdb28245-18ee-4848-a36d-4442ca167988.jpg 7519e7ee-6f39-4388-bec5-585c0a700bac.jpg f6a153c9-ad70-4e8b-a3b1-b7570b07311c.jpg

Hotpoint... | Answered on Sep 21, 2014


Hello & Welcome to FixYa

Someone accidentally put it into TEST mode and to get it out of the test mode follow this:-- Unplug the washer for 4 minutes and then plug it back and press start, the display should go daft. Press start again and the display should settle down. Now press the on/off button and the start button at the same time and hold them down for a few seconds until the display shows d-end or d-off. Please get back to me if you have any other questions.

Kevin

Hotpoint... | Answered on Sep 20, 2014


See my other reply to your request. It took me less than 2 secs on a search of your listed model to find a manual. One thing it says in the troubleshooting section is that if it fails to start with something showing on the display is to press and hold the start button for at least 3 seconds and the machine should start. See imagebank.indesitcompany.co.uk/brochures_online

Hotpoint... | Answered on Aug 29, 2014


Where is your user handbook? If you don't have one go online to the OEM who have most current models available for free download. If not get the model and serial number and search online. Call a local appliance agent for your brand, if they have a repair facility they may have a man who know's?

Hotpoint... | Answered on Aug 29, 2014

Not finding what you are looking for?
Hotpoint Aquarius WD640 Front Load Washer/Dryer Logo

906 questions posted

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

vince

Level 3 Expert

1234 Answers

gbob59

Level 3 Expert

3042 Answers

James Hehling
James Hehling

Level 1 Expert

11 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Hotpoint Washing Machines

  • Hotpoint Washing Machines

Most Popular Question

machine fault code f13

  • Washing Machines
Loading...