MPC Computers MPC F1760I 17" FLAT PANEL Monitor - Answered Questions & Fixed issues

AC Adapter For eMachines E15T3r 568 LCD Monitor Charger Power Supply... As you can see from the picture the power plug is a small round connector similar to an audio input. Power Connectors look for a connector like the DC socket in the picture

It is because your Windows monitor settings are OUT OF RANGE if you can boot into Windows normaly just rite click on the desktop, chose properties, than settings tab (if it's XP), go to advance, than monitor, look for frequency refresh rate, change to 60Hz, than save, than reboot

if you can't boot into Windows, try booting in SAFE MODE by pressing (F8) key at startup than do the above starting at -- rite click on the desktop...

Good luck!

You may have either the DC filter caps problem or the back light inverter board has failed, worst case will be bad lamps assembly. So check for 12vdc on the inverter board, bad caps with leaking/bulging top, bad solder joints.
Most common failures in the LCD monitors are bad capacitors (bulging top/seal or leaking) in the power supply, blown fuses, poor solder joints, failed inverter circuits (blown fuse, shorted transistors, shorted/open transformers), bad lamps (poor solder connections or worn out lamps). You will need to open it up and inspect the inside, see example of failed monitors to get some ideas what to look for: http://s807.photobucket.com/home/budm/allalbums
Post back what you see inside so we can guide you further and it will help out other people in the future also.
http://en.wikipedia.org/wiki/Capacitor_plague

IT righted itself

there is one possible way 1. remove hard drive from your laptop 2. plug your HDD into another laptop in anyway(usb or enclosure) 3. Make your HDD bootable with DOS mode 4. copy the new OS folder to your HDD 5. Put back your HDD to your old laptop then boot it with DOS 6. find the OS folder you copied, from there run setup your new OS.

You should be able to turn it off with MSCONFIG. Click START and type msconfig in the search box. You should see an msconfig entry show up near the top of the panel. Right click and pick "Run as Administrator". When the msconfig panel opens, select the General tab and make sure the Normal Startup is checked. Check the Services tab and make sure Enable All is on. Click APPLY and then OK, then YES for reboot. That should get you going.

some countries block these sites. Try going via a free web proxy (google for one) and see if this makes any difference although i would not been too keen to put your username and passwords in while using a free proxy as they may not be secure. The issue you have could also be with your security levels being set a little too high on your browser. You could try donwloading an alternative browser like Opera, Chrome, Firefox etc...

I use WebBlocker available for free from http://www.thewebblocker.com. Carries a couple of passengers but can decline the installation of these. Will block: Adult Material Social Networks Gaming and Gambling and more Can also block indevidual sites.

Yes you can. You might use Sugru to re-attach the cover. http://www.sugru.com

CHANGE YOUR USER ACOUNT SETTINGS IN CONTROL PANEL AL DOWN SECURITY

http://www.drivermax.com/ DRIVERPROGRAM.DO A SCAN.

yes. using a simple text editor like notepad simply add entries to the file: c:\windows\system32\drivers\etc\hosts the entries should look like this: 127.0.0.1 www.siteiwantblocked.com that IP address is the "localhost" and will result in and error or if the computer is running a web server it will go to that site.

On/Off switches are pretty basic, you should be able to find a replacement at any local electronics store.

make sure power is removed, open case and connect drive using the only cable that will fit.

Normally this happen when they are blue screen. Problem with RAM memory.You can test using the utility coming with the computer. Or go to the websiste from your supplier computer and download the utility for to test the RAM memory.+Update the computer with MicrosoftGod bless you

Motherboard should have the pins labeled. POW+ POW-Colored wire is + Black is - although the power switch doesn't really matter. Same with the LEDs they can be reversed and it wont hurt anything or work differently.

Try FN button + F3. It's an icon that looks like (kind of) the sun.

Try FN button + F3. It's an icon that looks like (kind of) the sun.

http://download.cnet.com/Drivers-For-Free/3000-18512_4-75548155.htmlif these dont work

http://download.cnet.com/slimdrivers-free/3000-18513_4-75279940.html

it might take some time being a freeware driver solution

note: it will find all of your outdated drivers

this is a free driver solutions they will automatically search for and find the correct driver also at cnet http://download.cnet.com/2000-20_4.html on the home page you should see a search tab just type in what you are looking for IE: motherboard name sound drivers you might have to try a few times to get it right

http://download.cnet.com/drivermax/3000-18513_4-10572602.html

Windows 2000/XP/Vista/7/8 free driver program

http://download.cnet.com/drivers-for-free/3000-18512_4-75548155.html

Windows XP/2003/Vista/Server 2008/7/8 free drivers

http://www.downloadcollection.com/device_doctor.htm

Device Doctor is a freeware Windows application that scans your computer hardware and checks to see if there are new driver updates available for your devices. It also locates drivers for Unidentified Devices in the Windows Device Manager. This tool was designed to be very simple and easy to use

http://www.innovative-sol.com/drivermax/ free program, paid update available

hope this helps

Install a set of Codecs. This is a small set of Standard Programs that allow the correct interpretation of the Audio and video files used on your computer. KLcodecs is a good place to start. They are free and should cover the vast majority of file formats.