20 Most Recent GE Asus P4GE-MX P4/Prescott/845GE/A&V&L/MATX Motherboard (MOTAS59) Questions & Answers

please check the connections. some of the wires inside your cpu maybe loosen up. so tighten them.

you can remove your video card and ram and use eraser to clean the leads.

or worst, your hard disk is corrupted.

Support/ Drivers Page:http://support.asus.com/download/download.aspx?SLanguage=en-us

Newer Manual:http://dlcdnet.asus.com/pub/ASUS/mb/sock478/p4ge-mx/e1862_p4ge-mx.pdf

Older Manual: http://dlcdnet.asus.com/pub/ASUS/mb/sock478/p4ge-mx/e1722_p4ge-mx.pdf

your drivers are here you will have to choose your operating system first
http://support.asus.com/download/download.aspx?model=P4GE-MX&SLanguage=en-us
Don't forget to leave posative rating andfeedback if this helps you

you can download the audio and vga drivers from the following links

http://www.megaupload.com/?d=SH4D9B4H
http://www.megaupload.com/?d=FF0TKP28

Get it checked from an expert. It may be due to overheating, or some other hardware problem. U can take a chance by reinstalling your operating system.

Number of PIN DDR2 more much than DDR1. If you install on DDR2 Slot DDR1, can not be installed correctly, because the location of the key slot DDR1 and DDR2 is different.

Look the picture, and look the different



I look for your maindboard, it's only supported DDR1.

The frequency failure is probably a message from the monitor to say it cannot cope. When setting resolution click "advanved" and try reducing the frequency.

try this 
http://support.asus.com/download/download.aspx?SLanguage=en-us&model=P4GE-MX

Does the compressor run? Or run intermittently? Are there any clicking sounds? Possibly the start relay is bad. It's a small box attached to the compressor. There should be 4 letters after the model number that you'll probably need to get the correct part.I'd give these folks a call: http://www.partstap.com/searchresults.aspx?model_or_part=TFX20JA

Try a GE Control Panel Reset This should clear the error codes: Power off the unit, wait 5 minutes then restore the power. Press the broil and bake keys simultaneously and "SF" will be displayed. Press "Hr. Down" and "Minute Down" keys simultaneously for 3 seconds, then the time of day will be displayed. Press "Temp Up" and "Minute Up." The control panel will display the following: Go blank briefly Display all segments briefly Display "LOC REF" briefly Display all segments again for 30 seconds Display "LOC REF" Acknowledge the "LOC REF" by pressing the "Hour Down" and "Minute Up." Test control pads. Oven should now function.

If the display on your GE refrigerator is not working try with this step: 1. Check the power: Make sure the refrigerator is plugged in and the outlet is working. If the display is completely dark, there may be a problem with the power supply. 2. Reset the unit: Try unplugging the refrigerator for a few minutes and then plugging it back in. This can sometimes reset the display and clear any error messages. 3. Check the temperature settings: Make sure the temperature settings are set correctly. If the temperature is set too high or too low, it can affect the performance of the refrigerator and cause the display to show an error message. 4. Consult the user manual: If the display is still not working or showing an error message, consult the user manual for troubleshooting tips and contact information for customer support. If none of these steps resolve the issue with the display on your GE refrigerator, it may be necessary to have a professional technician inspect and repair the unit.

yourspacebarisbroken,editinnsomespaces! Wecan'tpossiblyanswerquestionslikethis!

It is not uncommon for a Holter monitor to have a status indicator light that indicates the current status of the device. The color of the light and its meaning can vary depending on the specific model of the Holter monitor. In general, an orange light on a Holter monitor may indicate that the device is in a standby or charging mode, or that it is preparing to record data. It is important to refer to the user manual for your specific Holter monitor to determine the exact meaning of the orange light and any other status indicator lights that may be present on the device. The manual should also provide instructions on how to properly operate and care for the Holter monitor. If you are unsure about the meaning of the orange light or how to use the device, you should contact the manufacturer or a healthcare professional for assistance.

you don't. You may need to replace control panel

I saw this yesterday. The only way you can fix this is to take or all apart and remove the clock module and clean the top of the module and the back of the glass. Clean it with Fantastic Kitchen Cleaner and then polish with Windex. Check out the videos https://www.google.com/search?q=GE+JB555D+M2WW+clean+clock ..

I am making over $13k a month working part time. I kept hearing other people tell me how much money they can make online so I decided to look into it. Well, it was all true and has totally changed my life. Last month my pay check was $12712 just working on the laptop for a few hours.This is what I do, Read more here>>>HERE www.bizrecorder.com

https://www.manualslib.com/manual/1282845/Ge-Wiring-Devices-And-Specialty-Products-Ge5805ws6.html

It doesn't use WWVB so it's an internal clock calendar lookup. You might try removing batteries and reprogram... or set it back to 11:55 PM yesterday and see if it gets Tuesday correct. Then let it roll over into Wednesday on own and see if it does it right. If not, then likely a bad unit.

What is your question? General Electric has many divisions, from home appliances to generators for hydro dams to jet engines. https://www.ge.com/