Top 20 HP LaserJet 5si Printer Questions & Answers


If this is a "ghost" image like whats on the top of the page is re-appearing on the middle and/or bottom. The fuser is defective and needs to be replaced. Part # RG5-4447

HP LaserJet 5si... | 137 views | 0 helpful votes


Fusers generally make grinding noises more than cartridges do. If your paper jams are in the fuser area, check the fuser first.

When you open the left side door of the printer, the fuser is installed on a shelf near the top of the cavity. To remove the fuser, grasp the left and right blue fuser release handles and rotate them to the straight up and down (vertical position. Then lift up on the fuser and remove it from the printer.

Take a close look a the at the gear located on the top left corner of the fuser - does it have broken/ bent teet or is it loose on its mounting shaft? If so, that's probably causing both the paper lams and the grinding.

Also look in the printer directly under where this gear would be if the fuser were inserted in the pinter. Do tou see a build-up of fine particles the same color as the fuser gear. If you do that's further proof the the gear is bad.

You can but a replacement fuser at several places - check out www.printerworks.com & you can get one on an exchange basis.

HP LaserJet 5si... | 168 views | 1 helpful votes


What's the full message displayed?

HP LaserJet 5si... | 19 views | 0 helpful votes


Could be software. I have seen the last several Adobe latest version documents take several seconds to print. I have also seen increased print times with MS office 2003 Powerpoint documents.If it is a single page MS Word or Excel document and u are printing several copies of it, you should turn off the collate feature for printing of that document

HP LaserJet 5si... | 310 views | 0 helpful votes


i think your driver was wrong you need to download the best drivers
i hope i can help, you

HP LaserJet 5si... | 69 views | 0 helpful votes


Hi,

Several suggestions: 1. What operating system are you using? If it is Windows, then the printer tray can be selected in the Settings/Printers/Properties/Paper/PaperSource Note! You must have the correct driver installed. 2. The ESC&l#H sequence allows embedded commands to select trays. The info in the 5si Printer Users Guide (approx page 7-14)has some troubleshooting. The 5si printers at my workplace have automatic tray rollover. When one tray goes empty, it moves to the next tray with the correct size. Hope this helps.


Your issue is in defining which paper tray you want to use from the application side. Depending on your app I'm guessing MS Office when you've selected the 5Si in the printer select menu the print driver will know what tray's are available. The user must select the correct tray for a particular document and these setting will hold for this document. Otherwise the default for both trays with letter in them is to pull from the lower tray and when that runs out or is unavailable to pull from the next tray up with letter inserted. This link explains where the printer will pull from depending on how you set up both the app and/or control panel.

http://www.hp.com/cposupport/printers/support_doc/bpl02687.html


Thanks for contactng Fixya

HP LaserJet 5si... | 128 views | 0 helpful votes


Check tray 1 there should be an arm hanging down in the center of the tray the arm goes thru a slot in the metal plate. This arm moves when you install paper in tray 1. If the arm is missing or not in the slot the machine will think paper is in tray 1 and try to feed from tray 1. You can try changing the paper size setting for tray one to something other than the size in tray 2.

For example If tray 2 is set for 8.5x11 set tray 1 for legal.
The machine should then pull the correct size based on the print job.
Hope this helps

HP LaserJet 5si... | 556 views | 0 helpful votes


Turn off
Remove printer cable or
If it has a network card remove it
Turn printer back on
Let it come to Ready
turn off
re-install all cables / network card.

HP LaserJet 5si... | 298 views | 0 helpful votes


You need a PIU (paper input unit)...this has catches that lock in the tray. Usually, only one of the trays will not lock shut....but yours is a conicidence. Even if one tray didnt lock in, it is still the PIU.

HP LaserJet 5si... | 264 views | 1 helpful votes


You can try to clean the printers with some air cleaner , this usually helps to fix the problem. But due the age of your printers you will save money getting a new ones instead of try to fix them.

HP LaserJet 5si... | 109 views | 0 helpful votes


To change the 2nd pass roller, you need to remove the PIU(paper input unit).

Get a tech that has done it before. All covers have to be removed. Paper trays removed. It's not something that can be explained in an email.

HP LaserJet 5si... | 111 views | 0 helpful votes


Can you be more specific in the problem?

Also, please specify "how" you are connecting to the printer (parallel, LAN, etc)

HP LaserJet 5si... | 112 views | 0 helpful votes


Check the print processor settings in the advanced tab of the printer properties. This should be set to Winprint, and not anything else.

HP LaserJet 5si... | 487 views | 1 helpful votes


www.ettusaislashes.com Mink 3D Lashes3d faux mink lashes wholesale How to wear 3d faux mink lashes wholesale - Ettusais Lashes Company Wholesale premium individuals style soft natural 3d faux mink lashes wholesale .our mink fake lashes can customized,and can provide lashes package ,lashes tweezer and lashes brush.The price is cheap,and directly sell from our manufacturer.We can give you a big discount.
How to wear Mink 3D Lashes Ettusais Lashes Company

HP LaserJet... | 781 views | 1 helpful votes


The fuser may need renewal.
This is the 'heated roller' that melts the toner powder into the paper fibers.
A techie needs to check and renew.

HP LaserJet... | 30 views | 0 helpful votes


A problem with installation or functioning of the black cartridge

HP LaserJet... | 25 views | 0 helpful votes


49=Firmware error..........
Recycle the printer power (off/on). Test.
Switch off then disconnect all printer cables.
Recycle the printer power (off/on). Check Err.
Switch off and Reboot PC.
Connect all and test.
Try another app to print from.
Try print a different file.

HP LaserJet... | 24 views | 0 helpful votes


just happend, today, yesterday was ok, same setup?
or just got this from a garage sale and ...
or found it or barrowed it or >? tell the story please.
no PC stated
no OS stated (windows what?)
to run a printer on USB the printer needs to be reset first.
to USB mode, this is covered in the manual, lost that?
the USB port needs to be working , try them all/?
the HP software needs to be loaded too.
omg its 14 years old today. click software and then click change.
then pick your UNSTATED OS,in the huge list of operating systems this printer supports even up to w10

https://support.hp.com/us-en/product/hp-laserjet-4350-printer-series/412160/model/412162/manuals

HP LaserJet... | 34 views | 0 helpful votes

Not finding what you are looking for?
HP LaserJet 5si Printer Logo

Popular Tags

23 questions posted

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts

mukhtar21 shaikh
mukhtar21 shaikh

Level 3 Expert

2022 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18425 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

LaserJet HP

  • LaserJet HP

Most Popular Question

laserjet 5si printer jamming lot

  • Office Equipment & Supplies
Loading...