20 Most Recent HP OfficeJet 6110 All-In-One InkJet Printer - Page 9 Questions & Answers

Tip

Resolving the Paper Mismatch error on the HP allinone printer


Set the Paper Type settings to plain from the Printers properties window.
This will turn of the paper sensor on the Allinone and hence, you will not receive the error message again.

on Sep 20, 2011 | HP OfficeJet 6110 All-In-One InkJet...


try to disable Error Correction Mode (ECM).
to do so:
Press Menu . Press the Right Arrow (>) until Advanced Fax Setup appears. Press Enter . Press the Right Arrow (>) until Error Correction Mode appears. Press Enter . Press the Right Arrow (>) until Error Correction Mode ON or Error Correction Mode OFF appears. Press Enter . Send another fax to verify that the ECM is enabled or disabled.

HP OfficeJet... | Answered on Sep 19, 2011


Did you recently clear a print jam? Are all the little scraps cleaned out of the paper path and drive gears?

HP OfficeJet... | Answered on Sep 18, 2011


It is an hardware problem of printer, Just change the cartage with a new one then it will works.

HP OfficeJet... | Answered on Sep 14, 2011


Try here:-

http://h10025.www1.hp.com/ewfrf/wc/product?product=79477&lc=en&cc=uk&dlc=en&lang=en&cc=uk&y=10&x=7

if that doesn't work start at the HP support website.:-

http://www8.hp.com/uk/en/support-drivers.html

You will need to enter your operating system details as you go. You should be able to download, save and then install the driver you need. Also operating instructions and other bits and bobs if required.

HP OfficeJet... | Answered on Sep 12, 2011


alighment not sucessfully completed because of one of the catridge nozzles are clogged or carriage assm not reading the align page properly,check the align page is properly printed? if no repalce catridge, if print quality is good clean align reader which was located beside of the carriage... best of luck

HP OfficeJet... | Answered on Sep 07, 2011


hELLO IDEAL58ST,

While printing from the USB Port sometimes slow printout/data transfer will result in slow printing of print jobs. SOLUTION: Solution After the printer is installed on the USB Port, check the description under the Ports Tab what is selected. Please refer to the figure below : c00873625.jpg Using the USB/ Virtual Printer Port and DOT4/ HP Laserjet 2420, under the Port/Description Tab printer speed will be as per the standard. Whereas using the DOT4/ Generic IEEE 1284 under Port/Description Tab, Printer speed will be very slow. If DOT4/ Generic IEEE 1284 is selected by default, then you have to uninstall the USB driver from the Device manager and plug in the USB cable again. Then it will detect the printer and USB port with respect to the printer model.

THANKS.

HP OfficeJet... | Answered on Sep 06, 2011


I had exactly the same problem with my OfficeJet 6110 as reported above (i.e. the scan head not knowing where the end-stop is). This is how to fix it (this method worked for me) 1) Lift up the scanner/copier hinged lid. Around the edge of the scan glass are 4 Torx screws. Undo all four screws. 2) Carefully prise the control panel faceplate off. The buttons underneath are on a single panel. Slide this to the left and lift off. 3) Jiggle the lid of the scanner to get it off the main body of the printer. 4) Locate the scan engine motor (top right corner) and remove the two motor retaining screws (one on the left of the motor, the other on the right). 5) Lift out the entire mechanism (rod, drive belt, scan head) and turn over. 6) Thoroughly clean all glass and mirrored areas of the scan head. Also clean the scan lamp on the top of the scan head. Clean the tray inside the scanner (where the scan head travels back and forth). Also clean the inside and outside of the scanner glass pane itself. 7) Refit all parts, using the technique described above, in reverse order. 8) Switch on printer. It should now work OK. Hope this helps, guys.

HP OfficeJet... | Answered on Sep 01, 2011


Solution There are several reasons why the HP All-in-One may fail to align the cartridges. The most common reason is an ink cartridge that has one of the following problems:
  • One of the ink cartridges is low or out of ink. Black and all three colors must be available.
  • The paper has already been printed on or is colored paper.
  • Protective tape on a new ink cartridge has not been removed.
  • Contacts on the ink cartridge are not meeting the contacts in the carriage correctly.
  • Cartridge is remanufactured or refilled. Refilled or remanufactured ink cartridges may have been damaged during the refilling process or have clogged ink nozzles.
  • The ink cartridge is defective.
Follow the steps below to resolve the problem Step one: Examine the paper the alignment page was printed on The alignment page must be printed on clean plain paper of either letter or A4-size and that has a brightness level (as printed on the paper package) of at least 85. Colored papers or paper that already has printing on it will cause the alignment to fail. Back to top Step two: Does the alignment page print correctly For the HP PSC 900 series, if the page ejects immediately or a Paper mismatch or Paper too narrow message is displayed, the 4 x 6 paper tray selector located on the paper output tray is pushed forward. Move the selector all the way toward the front of the product. Look at the alignment pages that the product printed. Compare the alignment page to those that are included in the "Examples of alignment pages" section in this document. If any of the colors or the black is missing from your alignment page, a cartridge-related problem exists. Click here for information about troubleshooting ink- and cartridge-related problems (buu02176) (in English). Back to top Step three: Perform an print cartridge cleaning procedure The product can perform an print cartridge cleaning procedure even after the alignment message has displayed. Follow these steps to perform an print cartridge cleaning procedure at the front panel:
  1. On the front panel, press the Menu or Setup button (depending on the model).
  2. Press the right arrow button (>) until Maintenance or Tools is displayed, and then press the OK or Enter button (depending on the model).
  3. The Clean Print Cartridges message should display on the front panel. Press Enter or OK to begin the cartridge cleaning process.
A page will be printed during the cleaning process with all of the colors on it. If any of the colors (including black) are missing, faded, or streaked on the alignment page, there is a ink cartridge problem. Back to top Step four: Try to align the page again HP products have two methods for aligning the ink cartridges, fully-automatic and semi-automatic. The steps are different for each type. Refer to the information below to determine which alignment method your product uses. Automatic cartridge alignment Perform the following steps to align the ink cartridges:
  1. Disconnect the power cord from the unit, wait five seconds, and then plug it back in. This will reinitialize the unit.
  2. Print another alignment test page. If the Press Enter to align message is not currently on the front panel display, complete the following steps to print an alignment page:
    1. Press Setup or Menu on the front panel (depending on the model).
    2. Press the right arrow button (>) until Maintenance or Tools is displayed, and then press Enter or OK (depending on the model).
    3. Press the right arrow button (>) until Align Print Cartridges is displayed, and then press Enter or OK (depending on the model).
  3. To determine if the automatic alignment is functioning correctly, look into the output tray as the alignment page is printing; a blue light should be visible periodically on the page as the cartridges move back and forth. If this light is not visible, the product will not be able to align the cartridges and will require service. Service the product.
  4. If the blue light is visible and the alignment pages are printing correctly, but the alignment pages still fails, there still may be a hardware problem with the unit.

HP OfficeJet... | Answered on Aug 19, 2011


Please visit : HP OfficeJet 6110 All-In-One (Q1636A) parts Select the part you are looking for: jackpot00_158.jpg
Search for HP parts >http://partsurfer.hp.com/

HP OfficeJet... | Answered on Aug 13, 2011


You pick-roller is to dirty and need cleaning.take a clean cotton or cloth peace and with spirt clean the roller.If you look in the paper tray you will see the pick-up roller.Replay if you need futher help!

HP OfficeJet... | Answered on Aug 09, 2011


Replace all low ink cartridges before attempting the alignment.
The procedure can use a lot of ink.
if this doesn't work, disconnect the power from the unit
press and hold the [#] and [6] keys
connect the power - keep holding the keys.
The unit will either display "semi NVM reset" or it will shut off.
Release the keys. If the unit shut off, press POWER to turn it back on.
The printer will whir and gyrate for quite some time
wait for it to finish...it should do an alignment at the end of the procedure.
Make sure you have PLAIN WHITE paper loaded.
The unit should pass the alignment.

HP OfficeJet... | Answered on Jul 29, 2011

Not finding what you are looking for?
HP OfficeJet 6110 All-In-One InkJet Printer Logo

1,882 questions posted

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts

Clive
Clive

Level 3 Expert

4345 Answers

Thomas F. Schneider

Level 3 Expert

2715 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18429 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

OfficeJet HP

  • OfficeJet HP

Most Popular Question

setup scanner

  • Office Equipment & Supplies
Loading...