HP LaserJet 4250n Printer - Answered Questions & Fixed issues


GO ON LINE AND TYPE INTHE FOLLOWING INFORMATION; EXAMPLE:

HP LASERJET 4250N PRINTER ERROR MESSAGE KERNEL
ENTER
"" "" "" ILLEGALOPERTORSEQUENCE
ENTER
HP LASERJET 4250N ENDCHAR ERROR
ENTER
HP LASERJET 4250N PRINTER POSITION 24 ERROR
ENTER

HP LASERJET 4250N ERROR MESSAGE [ CODE # ]
ENTER

ROD THE CANDYMANGANDY

HP LaserJet... | Answered on May 02, 2019 | 653 views


Have a service tech check for the presence of the hi voltage applied to the paper to attract the toner.

HP LaserJet... | Answered on Mar 20, 2017 | 93 views


You have a print job on one of your computers. Probably a PDF
file you can change driver to a post scrip driver so you can print PDF files

HP LaserJet... | Answered on May 19, 2016 | 165 views


Typically these errors are caused when you have not upgraded the firmware on the printer, but are trying to print from newer software programs. The 49 error is basically the printer telling you it does not understand what you want it to do. HP Support Software Drivers Type in 4250 under the model here and then download the current firmware. Select the Easy Install version as you just have to run that like a regular program. This should resolve your issues.

HP LaserJet... | Answered on May 19, 2016 | 4,455 views


I would start by removing the old driver, and make sure the print Que is empty.
Did you upgrade the firmware? If not I would.

HP LaserJet... | Answered on May 11, 2016 | 814 views


check your print Que to see if you have a corrupt print job. cancel any and all prints in there, if any. if that doesn't solve it check/upgrade firmware or replace formatter board.

HP LaserJet... | Answered on Nov 18, 2015 | 140 views


Jams are most commonly caused by worn rollers in the paper pickup area. One roller is in the tray and there are two rollers in the body of the printer above the tray. The blue rollers are the feed and separation rollers, the while body roller is the pickup. You can try cleaning them with a damp cloth but depending on page count they might be too worn. Part numbers are Pickup roller RM1-0036 and feed/separation rollers are RM1-0037. If the printer makes a lot of noise when printing then it is possible that the fuser drive is worn and causing slipping.

HP LaserJet... | Answered on Feb 07, 2015 | 66 views


Sounds like a bad toner cartridge or a bad fuser. Try a different cartridge and also try running a cleaning page.

HP LaserJet... | Answered on Sep 21, 2014 | 66 views


60.2 is a lifter motor error, this is the motor that lifts the paper into position when you push tray 2 in. They do fail. Restart the printer and watch the paper level on the front of the tray to see if it moves at all. Also listen for any chattering noise is it does lift. Sometimes if the metal panel in the tray that lifts is not moving smoothly this error can occur. Pull the tray out and on the right hand side you will see a geared piece of plastic, rotate it to see if the tray lifts when you do. If not the tray might be the problem not the motor.

HP LaserJet... | Answered on Sep 17, 2014 | 150 views


Go to menu, in tray tray behaving tray1 select as unless paper load,in tray2 page size as any size.. while giving print command select printer properties, goto paper/quality select paper source automatic or tray2 & shoot print command & check...
# if you are not selected tray 1 as unless paper load, it will ask paper to load after command reached to it.
# if you are not selected tray2 as any paper size, defined paper size only it will allow to print..any paper size it will print with out questing you..

HP LaserJet... | Answered on Aug 02, 2014 | 590 views


It is an error with the laser scanner unit
1 Press ( SELECT button) to continue.
2 Turn the printer off and then on.
3 Reseat the connectors between the
laser/scanner and dc controller
PCA (J83 and J84).
4 Replace the laser/scanner assembly.
See Laser/scanner assembly.
5 Replace the dc controller PCA. See
Dc controller PCA.

If nothing from above works and the printer is no longer in warranty, it is possible if the printer is being used in a very dirty or dusty enviornment that the lens and optics of the laser/scanner are so full of debris that the beam detect error occurs. You can remove the top cover and the big black box in the center is the laser scanner assembly. Remove the screws securing the top cover of the laser scanner and remove and clean up all the optics to include the main mirror in the front. I usually use a damp q tip and for the mirror I slide up from toner cartrdige shutter area and observe from the top as it cleans the mirror. Removing the complete assembly on this model is not easy since there are a couple of cables going to the dc controller which are difficult to remove so removing the top of the assembly is easier.
Here is the service manual:
http://www.feedroller.com/Store/Service%20Manual/LaserJet%204250-4350%20(%204200-4300)%20sm.pdf

Click on this link or copy and paste the complete link into your browser.
If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe


I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

HP LaserJet... | Answered on May 05, 2014 | 7,590 views


Cancell all print jobs in the print que.. shut down computer disconnect USB or Network cabes to printer... turn printer off then back on wait till printer comes to READY then reconnect USB or Network cables ... turn computer back on and print again

I’m happy to help further over the phone at https://www.6ya.com/expert/ron_9356d26241d4cbf7

HP LaserJet... | Answered on May 03, 2014 | 1,169 views


It seems you have a worn fuserunit. By replacing the fuserunit (RM1-1083) the problem should be solved.
Gerrit Jan

HP LaserJet... | Answered on May 03, 2014 | 321 views


if no network cable is connected then it will always show as 0.0.0.0 this is because the network connection is not activated without a network cable

HP LaserJet... | Answered on Apr 07, 2014 | 174 views


download the user manual and look under 'setting timeout'
a function that can adjust the cutoff point - having said that I have never had to adjust the factory setting - I've allways found the error to be with the customer nertwork usually a conflicting ip address or poorly setup network
if you want to be sure that its nmot your network try pinging the printer via a dos window and have a look at the response time anything less than 100ms is good enough( usually 0.1ms) and if that is what you get when pinging then look at the network and not the printer

HP LaserJet... | Answered on Jan 28, 2014 | 106 views


have the machine perform a paper path test with just 1 copy to see if this jams then have it path test 5 prints to see when it jams- if its only jamming when more than one sheet is being printed then the fault lies with the paper pick up ( you may notice a longer delay for first print)
the machine will attemp to feed three times before failing as a jam
if the machine is printing more than one sheet then the jam appears just before the tail end of the first print exits the fuser (fixing Unit).
clean or replace the feed rollers.
if the jam happens on every print and the code is 13:02/3
then paper pass sensor arm 2 has stuck (look on you tube to resolve this search for lj4200 13:02 jam)
hope this helps- if you are still unable to get the machine working and your willing to pay then I would suggest Belmonte Buisiness machines
are a good company to deal with they are on 0161 480 5556 and can call out anywhere in the UK

HP LaserJet... | Answered on Jan 27, 2014 | 109 views


allow the machine to come to ready
press the TICK button press down untill Information press TICK press down until Print config pages press TICK - take config pages from exit tray
Done!

HP LaserJet... | Answered on Jan 17, 2014 | 362 views

Not finding what you are looking for?
HP LaserJet 4250n Printer Logo

313 questions posted

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts

Clive
Clive

Level 3 Expert

4345 Answers

Thomas F. Schneider

Level 3 Expert

2715 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18429 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...