Top 20 Tricity Bendix 24 in. BDW53 Free-standing Dishwasher Questions & Answers

Clean all filters: possibly the pump is blocked or it needs a new pump. Can you hear the pump working when it tries to empty?

Don't try it at home, please contact authorized service center. It may be hazardous, Please don't use it before Authorized Service Professional fixes it.

Hi


Dishwasher not draining issue usually occurs due to kinked drain pipe, clogged drain filter or drain pump. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remove then turn off the dishwasher and remove the drain hose and check for any visible clogging. If still not visible then the drain filter or drain pump is clogged and you'll need to clean the drain filter and drain pump. Also, check for any food pieces stuck near the pump impeller.
Please note that dishwashers don't drain out the complete water such that heating element doesn't overheat.
Hope this helps... Please post back for any further assistance.
Daniel

Yes there are brushes in dishwasher motors it sounds like they are either worn out or stuck try tapping motor with the wooden end of a hammer at the rear of motor as brushes clog up as they wear hope this helps

there is a new product out called the dishwasher filtration system. it actually filters the water going into your dishes. the dishes look dirty because your water has a lot of calcium and magnesium in it making them appear cloudy or dirty. the dishwasher filter reduces those minerals and my dishes look perfect now. no more dirty and grimy looking dishes. i also dont waste time washing them by hand before and after the dishwasher. hahaha you can get it at www.dishwasherfilter.com. use code DFMTEN and you will get 10% off. it fits right under your sink and is very affordable. you will be glad you bought this product. thanks

ensure the breaker has not tripped. Is your device controlled by a wall switch. Consult with electrician.

You know, I think the best thing to do would be to replace the dishwasher. It is ten years old and a new one would be more energy efficient and you would save money in the long run.

Any home appliance repair business can do this repair. Check the phone book or check online by zip code.

Generally the hoses haven't been attached tightly enough or there is a hole/split in one. Contact a service agent.

I gather that you are un the UK, Here is the spares store: http://www.ebay.co.uk/itm/Tricity-Bendix-BDW53-BDW60-DH102-TBDW41-BDW52-Dishwasher-Upper-Spray-Arm-/310859913118 IF this unit mounts under a counter you should take it out of the space under the counter so that you can see the top of the outside to see if there are any mounting bolts for the spray arm.

First, Is any water draining? If yes, look for restrictions or siphoning back into the machine. Hair and paper are common restrictions on the anti-siphon/overflow device. It's' on the sink top. Remove the cap, take a long nose pliers to remove the inner top plastic piece. Remove the junk - hair, paper, etc. Put a inverted cup and run the drain cycle. Move junk and water will come out. Re- assemble. Also check for kinks in the drain hose(s). Also clean out the filter and screen in the dishwasher. Watch out for broken glass. If new garbage disposer, make sure the knock out plug was remove -- should see water enter from the dishwasher. If you don't have an anti-siphon device, get one. Otherwise drain water will back into the dishwasher.

repair or replace get it from www.repairclinic.comGod bless you

You may download a copy of the manual here.

Your latch mechanism is out of adjustment if you lift bottom of door and press on handle with other hand it will remedy until you can adjust latch

Has it pumped all the water out as impeller can get trapped? in the case ther is a complex plastic eater control system that gets blocked in the corner, electric water valve, sump on bottom has water in it, good look

Possible that the INLET valve is faulty /clogged or there is no voltage to switch ON the inlet valve.
So measure the voltage at the inlet valve, also check if the inlet filter is clogged.
Check the water pressure at the inlet to confirm, remove the line from the inlet valve and confirm the flow when activated.

No. You need to remove the perforated floor of the machine to access the heater element, and you need to remove the rear cover to disconnect the wires. Once you have access to these points the job is actually very easy. Make sure that the power cord is removed from the wall socket before attempting any work on the machine.

Hi, I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works like new... However I have also foundthat if the heating element goes bad then that also can mess things up bad...So I would buy new spray arms, and also check out the heating element to makesure it is working... Here is a tip that will help you with the onlinebuying...
Dishwasher SprayArms not Spinning

How to Buy ApplianceParts Online

A bad heating element causes many problems in dishwashers...

Dishwasher Problems The HeatingElement not Working

DishwasherMaintenance DishwasherResidue and Film on Dishes

heatman101

Asker's Testimonial "explanation very clear. will give it a go and see howsimple it was. thanks Ronnie " - ronnieshomes

You have to remove the rear cover and the base cover inside the machine to reveal and access the element. Just make sure that the unit unplugged from the power outlet before attempting any work.

Hi,

Here is a tip that will help you to find out why water will not come into the dishwasher... Dishwasher Trouble No Water entering Dishwasher heatman101