20 Most Recent Zanussi ZWF1440 Front Load Washer Questions & Answers


Blocked filter or faulty pump

Zanussi ZWF1440... | Answered on Jan 10, 2018


E23 - Drain pump triac faulty
Could be: Drain pump faulty; wiring faulty; PCB faulty.

Dado

Zanussi ZWF1440... | Answered on Jul 06, 2016


E23 - Drain pump triac faulty
Could be: Drain pump faulty; wiring faulty; PCB faulty.

Dado

Zanussi ZWF1440... | Answered on Jul 06, 2016


Hello,
To display Error Code:
Move Programme Selector to the Off postion.
Press the 2 buttons on the right and turn the selector 1 position clockwise and hold the 2 buttons for about 5 seconds until all the lights are flashing. Release buttons and turn the selector to the 10th position. The Error Code will be displayed.
Note the code then turn the selector to off ,then on,then off again

when you obtain your error code message me back with what numbers your machine is showing and I will diagnose your error code for you. I await your reply Thanks
Rick

Zanussi ZWF1440... | Answered on Aug 21, 2015


It may be the child safety lock. There are often two buttons on the control panel which have to be pressed simultaneously (and held in) and they turn the lock off. The buttons should have a tiny picture of a lock underneath them.

Zanussi ZWF1440... | Answered on Feb 19, 2014


Disconnecting the wires from the main PCB helped resolve half the problem, but the machine still does not rinse and spin. Unless programmed manually. Still, that's easily done at the end of a wash cycle. Is liveble.

Zanussi ZWF1440... | Answered on Dec 25, 2013


Found These Fault Codes On Internet, Hope This Helps, Daz

ALARM CODES

E00(E00)- Problems with water fill during washing
-Tap closed; solenoid valve, water distributor, wiring ,main PCB, pressure switches

E01(E00)- Problems with water fill during drying
-Tap closed; solenoid valve, wiring , main PCB, pressure switches

E10(E10)- Problems with water drain during washing
-Drain hose kinked, filter blocked, drain pump, water distributor, wiring , main PCB, pressure switches

E11(E10)- Problems with water drain during drying
-Drain hose kinked, filter blocked, drain pump, pressure switches

E20(E20)- Door open
-Cycle in Door delay, wiring , main PCB

E21(E20)- Fault in door delay power triac
-Wiring , main PCB

E30- Fault in electronic pressure switch
-Electronic pressure switch, wiring , main PCB

E31- Fault in electronic pressure switch circuit
-Main PCB (fault in electronic pressure switch circuit)

E32(E10)-Calibration error in electronic pressure switch
-Electronic pressure switch, drain pump, wiring , main PCB, filter blocked

E33- Incongruency between electronic pressure switches and safety switch 1
-Electronic pressure switch, safety pressure switch,wiring, main PCB

E34- Incongruency between electronic pressureswitches and safety switch 2
-Electronic pressure switch, safety pressure switch,wiring, main PCB

E35- Intervention of anti-overflow pressure switch
-Solenoid valve, water distributor, wiring, main PCB,anti-overflow pressure switch

E36- Water leakage (maximum number of resets exceeded)
-Water leakage, drain hose too low, pressure switch,wiring, main PCB

E40- Motor power triac short-circuited
-Main PCB (triac short-circuited)

E41- No signal from tachimetric generator
-Tachimetric generator on motor, wiring, main PCB

E42- Fault in tachimetric generator circuit
-Main PCB (tachimetric generator sensing circuit)

E43- Intervention of motor overload protection
-Motor, wiring, main PCB

E50- Insufficient heating during wash phase
-NTC sensor setting incorrect, heating element, wiring,main PCB

E51- Overheating during wash phase
-Heating element (to earth), main PCB (relays)

E52- Insufficient heating during drying phase
-NTC sensor setting incorrect, safety thermostat,thermostats, drying heater, wiring, main PCB (relays)

E53- Overheating during drying phase
-Drying heater (to earth), main PCB (relays)

E55- Fault in power relay for heating element (K3)
-Safety pressure switch 2, wiring, main PCB- 6 -

E60- Fault in washing NTC sensor
-Washing NTC sensor, wiring, main PCB

E61- Fault in drying NTC sensor(condenser)
-Drying NTC sensor (condenser), wiring, main PCB

E62- Fault in drying NTC sensor(duct)
-Drying NTC sensor (duct), wiring, main PCB

E63- Fault in 1/2 power thermostat
-Drying NTC sensor (duct), 1/2 power thermostat, wiring,main PCB

E70- Power triac to distributor motor short-circuited
-Main PCB (triac short-circuited)

E71- Fault in power relay to distributor loads
-Main PCB (relay open)

E72- No distributor position signal
-Water distributor motor, wiring, main PCB

E73- Incorrect timing on distributor contacts
-Water distributor, wiring, main PCB

E90- Fault in tank fill pump
-Hoses obstructed, tank fill pump, wiring

E91- Fault in tank drain pump
-Hoses obstructed, tank drain pump, wiring

E92- Fault in power triac to tank fill pump
-Tank fill pump, wiring, main PCB

Zanussi ZWF1440... | Answered on Jan 08, 2013

Not finding what you are looking for?
Zanussi ZWF1440 Front Load Washer Logo

144 questions posted

Ask a Question

Usually answered in minutes!

Top Zanussi Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1479 Answers

jimorris77

Level 3 Expert

411 Answers

Marvin
Marvin

Level 3 Expert

84949 Answers

Are you a Zanussi Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Zanussi Washing Machines

  • Zanussi Washing Machines

Most Popular Question

aeg lavamat shows

  • Washing Machines
Loading...