L.Click on the APC Biometric Device Icon(fingerprint graphic, Figure 13 and 14), thefingerprint box will change color (Figure 14).Figure 14. Select Authentication Device Screen4 ENROLLFINGERPRINTOnce you have selected the APC Biometric Device icon,the Choose Finger screen (Figure 15) will be displayed.Figure 15. Choose Finger ScreenA.Click on the fingertip of the fingerprint you wish toenroll; a red arrow will appear above the selectedfinger (Figure 16). Click Next or Cancel.Figure 16. Selected Finger ScreenFigure 23. Audio and Taskbar Settings ScreenA.Click on the circle next to the desired selection, thenclick on Next, Cancel, or Start Over.B.Once the settings have been chosen, select Nextand the Congratulations screen (Figure 24) will bedisplayed. Click Done to complete the enrollmentprocess; the Logon New User screen (Figure 25) isdisplayed. Click Yes to logon the new user, or clickNoto stop the installation process.Figure 23. Congratulations ScreenFigure 24. Audio and Taskbar Settings ScreenC.If you clicked on Yes to logon the new user, theLogon User Authenticationscreen (Figure 11) isdisplayed. Place your finger on the Sensor andDrive Ring. The system will read your fingerprint andlog you onto your computer.At this time, you should restart your computer toensure the setup is complete. During restart, yourWindows logon screen will appear. Within a fewseconds, the Logon User Authentication screen(Figure 11) will also appear. You can either enteryour Username and Password, or simply place yourfinger on the Sensor and Drive Ring of the BioM34.Upon authentication, the BioM34 will automaticallyfill in the Windows logon screen and log you ontothe computer.B.The software will then display the Blank CaptureFingerprintscreen (Figure 17). Place the choosenfinger over the Sensor and Drive Ring (Figure 18).Figure 17. Blank Capture Fingerprint ScreenNote: Place the finger on the BioM34 sensor anddrive ring (Figure 18) for scanning. Use light, but firmand steady pressure. Ensure the finger makescontact with the BioM34 sensor and the surroundingdrive ring. APC OmniPass works best when it hasan image of the center of a fingerprint (core image).Capture the full area of the fingerprint by placing thefinger flat on the BioM34 sensor. Do not place onlythe fingertip on the sensor, as it contains insufficientimage data for a high-quality fingerprintFigure 18. Sensor and Drive RingC.As you place your fingertip on the Sensor and DriveRing (Figure 19), the system will record yourfingerprint and display it in the gray box (Figure 20)and the box numbered “1” will turn green. You mustraise the finger straight up and put it back on thesensor up to 8 times before the fingerprint issuccessfully recorded. Each time the fingerprint isrecorded, another numbered box will turn green.Figure 19.Finger PlacementFigure 20. Capture Fingerprint ScreenD.Once the device has successfully recorded yourfingerprint, the system will display the VerifyFingerprintscreen (Figure 21). Place your finger onthe Sensor and Drive Ring.Figure 21. Verify Fingerprint ScreenE.After the system has verified your fingerprint, it willthen ask if you would like to enroll additionalfingerprints (Figure 22). To enroll additionalfingerprints, click Yes. To stop, click No.Figure 22. Additional Fingerprints Prompt5 SELECTAUDIBLEANDTASKBARSETTINGSAfter enrolling and verifying your fingerprint, the systemwill allow you to set certain audible prompts, as well aswhat is displayed in the taskbar located at the bottom-right side of your display (Figure 23).I.After restarting your computer, the Windows log-inscreen will appear. The Omnipass software will alsodisplay a Logon User Authentication screen(Figure 11). Enter your User Name and Password inthe Windows logon screen. You do not have to doanything with the Logon User Authentication screenat this time.Figure 11. Logon User Authentication ScreenJ.The software will then display the Verify Usernameand Passwordscreen (Figure 12). Enter yourWindows Username, Domain, and Password.Figure 12. Verify User Name and Password ScreenK.Once logged into the Omnipass software, the SelectAuthentication Devicescreen is displayed (Figure13).Figure 13. Select Authentication Device Screen
Guru