20 Most Recent
NEC Galileo 845GL (N4-IBFGL) Motherboard - Page 2 Questions & Answers
Can vista run in intel 845gl mother bord
the minimun requirements to run vista on any motherboard should be as follows but yes it will as long as you have these
- 1 GHz 32-bit (x86) or 64-bit (x64) processor
- 512 MB of system memory
- 20 GB hard drive with at least 15 GB of available space
- Support for DirectX 9 graphics and 32 MB of graphics memory
- DVD-ROM drive
- Audio Output
- Internet access
Mother board driver
If you can not retreve your drivers direct from NEC, you can go to driversguide.com
No sound
do you have sound driver??? re-instal sound driver maybe can fix it...
I have install windows xp on my pc but no sound is
hi,
it sounds like there are drivers missing.
click start the right click on mycomputer and select properties click on hardware tab then device manager.
A list of all your hardware will pop up and will tell you what bits of your hardware arnt working and missing drivers
If you tell me you soundcard model number and manufacturer details i will try and get you the drivers, if you have onboard sound ie the the sound card is built into *********** board then send me details of your motherboard e.g asus a8n-e etc and i will find you the drivers and send you the link so you will be up and running again
Not powering on
First you need to try removing ram and connect again. It normally occurs .. for me too.
And please comment here on update, if it works and if not..
Need driver Motherboard
i need n4-ibfgl motherboard driver for
ethernet controller
audio driver
vedio driver
please help me.....
I have the same problem
i have nec gigabyte n4 ibfgl v 1.2 mother board . i have format the pc & had install windows service pack 2 but now only audio sound & lan that is internet connection was not working
USB connectors plroblem
Excuse me, I don't usually do this but for me to give the full story would take me hours so I've found a link for you to follow and I think it's the best I've seen.
http://www.directron.com/installusb.html
BMW
Foxconn motherboard red light and nothing else
Remove all connectors and cards except vga and power supply. and one stick of memory and start there.
If its still an issue remove the board from the case , it may be shorting out on something and try it outside the case,
check the power supply switch for 110/220v switch on back if it has it.
to manually trigger the power supply on the 24 pin connector
short the green and black wire that is next to it.
Motherboard
Well, you will need the model # at least, as it seems Soltek is no longer a viable company on the internet, i.e. no website that can claim to a manufacturer website.
But if you can deliver the motherboard Model #, chances are we can find a driver that will work for you.
Mother board not working properly
disconnect the power connectors from the board
on the large connector short out the green and the black wire next to it. does it come on.
if not it is dead.
Restarte again and agian
check your cmos CR2032 battery on the motherboard as this can cause restarts because of bios settings,when booting press F2 or Del and check the date and time to see if incorrect.
Also it maybe a faulty driver causing the crash, you can tell the bios to halt on all errors instead of rebooting, this can be found in the main cmos settings menu normally below the list of drives and check to see if halt on all errors is enabled, this way you can try to see what is causing the reboots.
Please give good solution ....
A little more info for your motherboard is required but you can decide for yourself at the link below as to which drivers you require, as you will need to look at the chip on your board as to know which driver you need.
http://www.nec-computers.co.uk/support/Search.asp
What software or cords do I need to get/run in order to get files to transfer to/from the NEC Mobilepro 770, or even get internet?
The NEC Mobilepro 770 is a legacy device that was released in the early 2000s and uses Windows CE as its operating system. Since the device is no longer supported, it may be challenging to find software and drivers that are compatible with modern operating systems like Windows 10. Here are some steps you can take to transfer files and connect to the internet:
- Get the necessary cables: You'll need a USB cable to connect the Mobilepro 770 to your Windows 10 PC. The cable should have a USB Type-A connector on one end and a mini-USB connector on the other.
- Install ActiveSync: ActiveSync is software that allows you to synchronize files between your Mobilepro 770 and your PC. Unfortunately, ActiveSync is no longer available for download from Microsoft, but you may be able to find an archived version of the software on the internet. Install ActiveSync on your Windows 10 PC and connect your Mobilepro 770 to your PC using the USB cable. If the device is recognized, you should be able to transfer files between the two devices.
- Connect to the internet: The Mobilepro 770 has a built-in Ethernet port that you can use to connect to a wired network. To connect to the internet, you'll need an Ethernet cable and a wired network connection. Plug one end of the Ethernet cable into the Mobilepro 770's Ethernet port and the other end into your router or modem. You should be able to browse the internet using the Mobilepro 770's built-in web browser.
- Install additional software: The Mobilepro 770 comes with a basic set of software, but you may want to install additional software to make the device more useful. You can download and install software from the internet, but make sure it's compatible with Windows CE and the Mobilepro 770.
Keep in mind that the Mobilepro 770 is a legacy device, and its performance and capabilities may be limited compared to modern devices. It's also possible that some of the software and drivers you need may no longer be available or supported.
Not finding what you are looking for?