Gateway Belkin 54g Wireless DSL/Cable Router (DHF5D72304) - Page 2 - Answered Questions & Fixed issues

Un-install Google Chrome, run c-cleaner , reboot, re-install.

To RESET the Netgear, power up the Netgear then press andhold the RESET button at the back of the router until all the LEDs flash.Connect a LAN cable from the Netgear to the LAN port on yourcomputer, open a browser and enter the Netgear configuration URL -http://192.168.0.1The default login = adminThe default PW = passwordYou can now change the default admin password and configurethe wireless settings.Go to the wireless configuration and set up the SSID and WPA or WPA2encryption.Apply these settings to the wireless card in your laptop/computer.To secure your wireless network from unauthorized access, please click on thislink and follow my instructions :-http://www.fixya.com/support/r3559128-wireless_router_security

See How to change NAT type to open

go to router configuration page in that wirless is there option in that seciurty option is there then give the wep or wpa option then give the password then save it re-try it to connect

How you connect to the router configuration page is depended upon how you have your router management configured. I believe by default belkin routers allow for remote configuration so if you didn't configure any security on your router someone may have altered your configuration.The default method for configuring your router requires.

• An ethernet cable plugged from your computer to a LAN port on the router
• The correct Gateway address (Start > Run > Type "CMD" at the command prompt type "ipconfig" look at your gateway address
• In a web browser type in http://192.168.0.1 in this example

If you still can't access it I'd suggest pressing the reset button on the back of the router and re-configure the router in case of tampering.Comment if you need any further assistance

On the back of your router there is a reset button, hold it down for 3o seconds or so, this will reset the router back to factory settings, the default user name and password would be admin, note that sometimes with the belkin you only need the user name and not the password. Usually you need admin/admin though.

The default IP address to access the router when its reset is 192.168.2.1

Hope that helps

hi,
if you are wired as described there are no ports to open on your router. you are in the same vlan(IE:192.168.0.1/254) so no port routing is needed unless you are accessing them from the outside world which is what your router seperates you from.
however that means the systems can in theory talk to each other but you are now onto firewall rules of each system. effectivley only the mysql server need alllow inbound as outbound is usually not blocked. you can test if you are having a port issue by opening a command prompt and type telnet server_host 3306 (where server host is the ip or name of the server ) If you get a connection and some garbage characters, the port is open, If telnet hangs or the connection is refused, the port is blocked,
all that being said I would recommed you close any ports from the outside that don't absolutly need to be open.
GL
Hope this helps
please don't forget to give me a rating
Thanks

Jammer

1. Try to RESET both the router and modem, by unplugging the power for about 30 seconds.
2. Recheck your connection after about 2 minutes.
3. If not ok, contact your ISP for your STATUS.

Are you connected directly to the router with a ethernet cable or no?

It's mapped automatically by your ISP, the real question is what are you trying to accomplish?

• Are you looking to trying to run some type of service, host a web server, ftp etc?
• Are you trying to enable a remote connection to a PC/server behind a nat router?
• Are you wanting to configure a dynamic IP? (This maps a host name ex: myhomeserve.somedomain.com to your non static ip assigned by your ISP)

Please comment back so I can help you!

hi,

i think you had better to see this link : here

because i dont know what OS you are using ?

you don,t describe how you are setting the router with your PC or TV ?


so refer to above link , hope to find ano solve the problem.


good luck


gorbesia

that wont be causing it, i would try changing the wireless channel on your router, also ensure that no electric devices are too close to the router and its not surrounded by cables

Hi Craig,

First I suggest you remove the second IP address as this is your public address most likely that should not be posted in the open online for all to see. That being said, have you attempted to perform a full reset on the router? This is performed by holding the small pinhead button on the back of the router down for about 30 seconds while plugged in. Once done you can set the router back up like you did when you first purchased it.

You can find the manual for your router as well as possible firmware updates on the following page. (Have your model # handy!)

http://en-us-support.belkin.com/

pleas give me the detail explanation why your device was no acces to internet

There is a great article at Working with Windows Wireless Networks
If you need more help post back! Thumbs and testimonial are welcome!

If you're talking about your wireless network key: you can find this in the modem settings. Take a closer look at the manual to see on how you can visit your modem interface to view or change these settings. For most modems this involves connecting your PC using a network cable (just for the sole sake of looking up the key, don't worry) and the surfing to your router's IP address.

Did you connect the lan cable to the right port ????

1. Shut down any programs that are running on your computer at

this time.

2. Make sure you have the following items at the computer that is now

directly connected to the cable or DSL modem. DO NOT CONNECT THE

ROUTER AT THIS TIME.

• The Easy Install Wizard CD-ROM

• The Router

• The Router power supply

• Category 5 networking cable

• This Quick Installation Guide

3. Turn off any firewall or Internet connection sharing software on

your computer.

4. Insert the Easy Install Wizard software CD into your CD-ROM drive.

The Easy Install Wizard screen will automatically appear on your

screen within 15 seconds. If it does not, select your CD-ROM drive

from "My Computer" and double-click on the file named "Setup" on
the CD-ROM.

5. Turn on your cable or DSL modem by reconnecting the power supply to The Wizard will take you through the completion of the process.

the modem.

6. Before plugging the power cord into the Router, plug the cord into the

wall, then plug the cord into the Router's power jack.

7. Verify that your modem is connected to the Router by checking the

lights on the front of the Router. The green light labeled "WAN" should

be ON if your modem is connected correctly to the Router. If it is not,

recheck your connections.

8. Verify that your computer is connected properly to the Router by

checking the lights labeled "LAN 1,2,3,4". The light which corresponds
to the numbered port that you connected your computer to should

to the numbered port that you connected your computer to should be
ON if your computer is connected properly.
The Wizard will take you through the completion of the process.

Good luck

go into Internet Explorer or similar and write in address field 192.168.0.1 or else 192.168.1.1 and logon then adjust your name in wireless settings panel.

Hello,
If you require the WEP key for the wireless network you will have to log in to the router interface and retrieve it. You can try the following steps..
1) Open internet explorer on any computer connected wired to the router. ( IF no computer is connected then connect your laptop through an Ethernet cable to the LAN slot on the router) 2) Delete everything from the address bar and type http://192.168.2.1 and hit enter. 3) Towards the left side under wireless click on security. 4) Now it will ask for the login password, do not type anything..just hit enter. 5) Now you will be in wireless security page. You should see Key 1, Key 2, Key 3 and Key 4. The check mark selected on either of the four with number or numbers and letters in it are the password. Make a note of it. 6) Now connect to the wireless network using the keys u made a note of.
Hope this helped.

There a great article at General Router Setup.
If you need more help post back!
Thumbs and testimonial are welcome!