Linksys Wireless-G WRT54G Router - Answered Questions & Fixed issues


No, but you can just reset the whole router and start from scratch. Hold the reset button on the rear of the router for 60 seconds and your will restore the unit to defaults, at which point you just need to reconfigure all of your configuration settings and password, as well as your wireless access code. Let me know if you require any additional assistance.

Linksys... | Answered on Mar 31, 2018 | 199 views


Resetting the linksys router in just six easy steps..
1. Turn on the router.
2. Reset the router, wait until the power light is blinking and then press and hold the reset button for 10 second.
3. Turn off the router and turn on again.
4. Wait for the power light to stop blinking, if the power light does not stop blinking, turn the router off, wait approx 30 second , and then turn it on again.
5. Connect the router to your computer, when it is connected to a computer with an ethernet cable, the ethernet port light will light up.
6. Connect the router to your modem, the modem is connected to the internet port is your computer. The router is connected to the modem.
If you are not able to reset the linksys router password then call linksys router support phone number 1-888-494-1155 (Toll-free) USA.

Linksys... | Answered on Feb 12, 2018 | 261 views


Are you trying to open the router setup page? Make sure that your computer is connected to the router on LAN port. Check the IP address on the computer and Default gateway. Default gateway is the IP address on your router.
Try this link
Linksys WRT54G router setup and troubleshooting

Linksys... | Answered on Jan 03, 2018 | 147 views


Make sure that computer is connected to the router on LAN port (1, 2, 3, 4). Also check the ethernet light is also lit on the router. Check the IP address on the computer connected to the router. Check this link
192 168 1 1 How to set up

Linksys... | Answered on Jan 03, 2018 | 105 views


Look on the back of your router for a url (numerical Web address) that is the format of 123.456.7.8 In your PC Internet browser put said url in address bar and connect to your router. Your user id should be on the first page. If you have forgotten your password contact your service provider to reset.
However your user ID and preset password should be on the sticker on the back of your router. If none of this works contact your service provider.
11_23_2017_9_46_43_am.jpeg

Linksys... | Answered on Nov 23, 2017 | 233 views


You need to check the ip address of your actiontec router, the default ip address of linksys router is 192.168.1.1, they should not be the same or else you will not able to connect the router to the internet.

To access the router web configuration
http://linksys.custhelp.com/cgi-bin/linksys.cfg/php/enduser/std_adp.php?p_faqid=3676&p_sid=fvzPHEYi&p_lva=3687#

http://www.linksys.com/servlet/Satellite?c=L_CASupport_C2&childpagename=US%2FLayout&cid=1166859837401&pagename=Linksys%2FCommon%2FVisitorWrapper&lid=3740145678B574

Let me also give you the site on how to add the linksys router to another existing router.

The linksys has 4 LAN port and 1 "Internet" port on the back - we ONLY use the LAN ports NEVER the Internet port - because your existing router is connected to the Internet - your linksys is connected to the LAN

http://www.kriyayoga.com/love_blog/post.php/368

Linksys... | Answered on Nov 23, 2017 | 853 views


Default user names:
  • Linksys BEFW11S4, WRT54G: admin
  • Linksys EtherFast Cable/DSL Ethernet routers: Administrator
  • Linksys Comcast routers: comcast
  • All other Linksys routers: [none]
Default passwords:
  • Linksys BEFW11S4: [none]
  • Linksys Comcast routers: 1234
  • All other Linksys routers: admin

Linksys... | Answered on Nov 23, 2017 | 251 views


Here is a link to the Linksys WRT54GL Wireless-G Broadband Router support site with manual and firmware downloads

Linksys... | Answered on Nov 04, 2017 | 226 views


Hello
Try a different wall plug.If this does not bring the light to green the you probably need a new power cord.

Here is a link for your router.

http://homesupport.cisco.com/en-us/wireless/lbc/WRT54G2

Linksys... | Answered on Sep 14, 2017 | 173 views


Try a different ethernet cord if you haven't already.

Linksys... | Answered on Sep 01, 2017 | 94 views


have you tryed bridge mode on the modem
which device is doing the routing dhcp only one can do the dhcp
is the internet light lit on the router, the router is set for ppoe for dsl
try turning off dchp on the router let the modem handle

Linksys... | Answered on Jul 06, 2017 | 368 views


Pull the Linksy out of the console of your computer then re-install it. You may need to press and hold down your router for 30 seconds and then re-press.

Linksys... | Answered on Jun 29, 2017 | 31 views


I'm sure your answer lies in the prior advice. However, from time to time, it is worth checking: http://downforeveryoneorjustme.com/

Linksys... | Answered on Jun 29, 2017 | 46 views


I need help getting code for my router

Linksys... | Answered on May 12, 2017 | 90 views


I have att yahoo dsl which I installed about a year ago. The process required bridging the ADSL Modem (in my case a speedstream 4100) and accepting dynamic IP addresses and configuring PPPoE on the WAN side of my Linksys router. The ATT support person walked me through the entire process over the phone even though I was comfortable with making the Linksys configuration changes as I had to do the same in China without technical support. The modem configuration was no more difficult than the router configuration as it was performed from a web browser too. The biggest warning was that to reverse the modem change (if desired) required use of a reset button because the web interface was disabled as a result of the configuration change. My advice to you especially if you are willing to attach the Linksys router to the telco modem is to contact the ATT highspeed DSL support line and see if they will walk you through it like they walked me through it. Reviewing your Linksys User's Guide and understanding the configuration of that device would probably be appreciated by the ATT Support person as well as assuring you can access the Linksys router to configure it during the call.

Linksys... | Answered on Apr 03, 2017 | 1,220 views


Is the acer wired to the router? call linksys technical support, if they cannot help try this http://technicalsupport.blog.friendster.com

Linksys... | Answered on Apr 03, 2017 | 206 views


There is a small reset button on the rare side of Linksys router. You need to press that button.
Remember if you reset the router, it will come back to factory default settings and you will need to reconfigure it.
See How to reset Linksys router

Linksys... | Answered on Feb 11, 2017 | 461 views


sometimes this router are afected by the lightnings, verify that the internet connection is working well by plugin the internet(ethernet) cable directly to your computer, if it gets connected to the internet we are sure the probleme is isolated to the router.
The easiest way to check if the problem is the router WAN(internet) port would be connecting a known good router just for few minutes

Linksys... | Answered on Jan 07, 2017 | 258 views

Not finding what you are looking for?
Linksys Wireless-G WRT54G Router Logo

4,209 questions posted

Ask a Question

Usually answered in minutes!

Top Linksys Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2263 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Michael Galve
Michael Galve

Level 3 Expert

1269 Answers

Are you a Linksys Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...